My Mogra Reed Diffuser Develops Sediment After a Week — Should I Investigate the Fragrance Oil’s Compatibility with the Carrier?
Aktie
What is the first test? Fill small clear jars, capped and without reeds: your base alone, your mogra alone, your formula at 20%, 15% and 10%, a known jasmine in your base, your mogra in a second base, and the failing liquid filtered and unfiltered. Read them on days 1, 3, 7 and 14.
Can I filter it and sell it? No, not on the first batch. If the sediment comes back after filtering, the formula is still separating. Quarantine the stock until a fresh batch passes the screen and a 21-day reeded test.
What does CSI sell for this? CSI’s Mogra 100 g was out of stock on 7 October 2026, so this page works with your own mogra. The screen kit (two packs of 50 ML bottles, Softness Base, a 50 g jasmine control and a beaker) is ₹3,281.00; bottles alone are ₹1,652.00.
- Straight answer: compatibility, or something else?
- Read the sediment before you test it
- The cause table: oil, load, base, reeds, bottle, room, process
- Stage 1: the fifteen-jar sealed screen
- Stage 2: twenty-one days with reeds
- What to do with the stock you already made
- Mogra at CSI, kit prices and the run after a pass
- What to buy
- Frequently asked questions
Read the sediment before you test it
Your situation, restated: a mogra reed diffuser, clear on the day you made it, shows sediment after about a week. The title gives no load, base, reed count or room, so this page assumes the series default, 20% (20 g mogra + 80 g base per 100 g) in a 120 ml bottle with a 100 g fill and six reeds; if your load is different, shift the screen’s three loads around yours. Before you mix anything new, look closely at what you have.
| What you see | What it often points to | Quick check | Then |
|---|---|---|---|
| Fine glittery specks or needles that settle | A material crystallising out of solution | Warm the sealed jar gently in your hand for 10 minutes: do they shrink? | Load ladder and cool cycle (Q3) |
| Soft, cloudy flocs or a waxy film at the base | Less soluble components separating from the carrier | Swirl: do they cloud the liquid then resettle within hours? | Carrier arm (Q4) and load ladder |
| Dark grit or fibres | Dust, reed debris, a dirty beaker or cap | Do the specks look different from each other? | Process and reeds (Q1, Stage 2) |
| Clear droplets or a separate bottom layer | Water or an immiscible ingredient | Does the layer stay clear and sharp-edged? | Base blank and process (Q1) |
| Haze throughout, no settled layer | Cloudiness, not sediment | Does it clear when warmed? | See the rose cloudiness post |
| Sediment only where reeds stand | Liquid concentrating as carrier evaporates, or shedding | Is a capped retained sample clear? | Stage 2 sealed-vs-reeded check |
Keep a sealed retained sample of every future batch for exactly this reason: a capped jar of the same liquid on the same shelf separates "the formula sediments" from "the diffuser sediments". If you didn’t keep one this time, jar H in the screen is the stand-in: liquid poured from the failing diffuser into a clean capped jar. Haze and cloudiness at mixing are a different gate, covered by CSI’s live guide on cloudiness after mixing and physical compatibility; this page owns sediment that appears days later.
The cause table: oil, load, base, reeds, bottle, room, process
"What you’d see" is what makers commonly report, not CSI test data. Each discriminating test isolates one source.
| Cause | What you’d see | Discriminating test | Fix |
|---|---|---|---|
| Oil · less soluble components | Flocs or crystals in every load, worse at higher % | Jars C, D, E: sediment falls with load | Approve the clear load, or change oil |
| Oil · lot or supplier | New bottle of "the same" mogra sediments; old one didn’t | Neat-oil jar B; old lot vs new lot side by side | Lot approval (re-qualifying a changed oil) |
| Oil · colour or oxidation | Dark specks with colour change | Dark vs light storage of twin jars | See the yellowing rose post |
| Load · past the carrier’s limit | Clear at 10–15%, sediment at 20% | Jars C vs D vs E | Lower load |
| Base · solvency mismatch | Your base sediments, a second base doesn’t | Jar C vs jar G | The carrier that stays clear |
| Base · the base itself | Sediment with no oil at all | Base-only jar A | New base lot; ask the supplier |
| Reeds · shedding | Fibres or grit only in reeded bottles | Stage 2: sealed vs reeded, fresh reeds | Different reeds; rinse-free handling |
| Bottle and cap | Specks in some bottles only | New, rinsed, fully dried bottles | Clean, dry bottles and caps |
| Room · cool nights | Crystals in the morning, fewer by afternoon | Cool-cycled twins vs room twins | Lower load; warmer storage is not a fix for customers |
| Process · water, dust, shared tools | Clear droplets, grit, varying bottle to bottle | Jar A plus a fresh batch with dried tools | Dedicated, dry beaker; covered mixing |
Stage 1: the fifteen-jar sealed screen
| Jar | Contents | Batch | Jars | What it answers |
|---|---|---|---|---|
| A | Your base only | 100 g base | 2 | Is the base (or your process) the source? |
| B | Your mogra, neat | 20 g oil | 1 | Is the oil lot itself settling? |
| C | Your formula at 20% | 20 g + 80 g | 2 | Does a fresh, clean batch reproduce it? |
| D | Mogra at 15% | 15 g + 85 g | 2 | Does less oil reduce it? |
| E | Mogra at 10% | 10 g + 90 g | 2 | Where is the clear load? |
| F | CSI Jasmine at 20% in your base | 20 g + 80 g | 2 | Does your base sediment with florals generally? |
| G | Mogra at 20% in Softness | 20 g + 80 g | 2 | Does a second carrier hold it? |
| H | Failing diffuser liquid, filtered | from the bottle | 1 | Does sediment come back? |
| I | Failing diffuser liquid, unfiltered | from the bottle | 1 | Reference for H |
Materials: 85 g of your mogra (65 g for jars B to E plus 20 g for jar G), 435 g of your base, 80 g of Softness Base, 20 g of CSI Jasmine, 15 clear 50 ML bottles and a clean, dry beaker. Use one lot of each material, and the same mogra bottle the failing diffusers came from.
If your mogra passes in Softness but not in your base, that is a carrier result for this oil, not a verdict on either base in general. The broader method for choosing a base that stays clear with a given oil, before you buy it in quantity, is in CSI’s live guide on compatibility tests before buying 5 kg of base.
Stage 2: twenty-one days with reeds
Take the passing liquid with the smallest change and run it against your current formula as diffusers: 2 arms × 3 bottles = 6 bottles of 120 ML, 100 g fill, six fresh reeds each, on one shelf for 21 days. Keep a sealed 40 g retained jar of each liquid beside them. If both arms are at 20% you need 120 g of mogra; less if the winner is a lower load.
| Check | When | How | Pass (in-house) |
|---|---|---|---|
| Sediment in reeded bottles | days 7, 14, 21 | Torch and white card, tilt gently | Score 0 in all three bottles |
| Sealed retained jar | days 7, 21 | Same reading | Score 0 |
| Weight loss | every 3 days | (start − end) ÷ days on a 0.1 g scale | Within your life target |
| Reed tips | day 21 | Lift one reed: colour, grit, tackiness | No grit or crust |
| Room scent | days 7, 14, 21 | Coded bottles, blind 0–5 at 3 m | Not weaker than the current formula by more than its own bottle spread |
Reading it: if the reeded bottles sediment but the sealed jar stays clear, the liquid is concentrating as it evaporates (or the reeds are shedding; fresh reeds in a clean bottle tell you which). The fix is usually a lower load, so the liquid has headroom as it concentrates. If a lower load costs you room strength, that trade-off belongs to the floral load-ceiling post; whether the mogra still projects from a reed at all is the bottle-versus-room mogra post.
What to do with the stock you already made
Quarantine it: label the batch, stop sales and keep two bottles as references. Don’t pour liquid back into the mixing vessel or top it up with fresh liquid. Once the screen names the source, decide: if the cause was contamination and a fresh, clean batch passes both stages, remake the stock from scratch rather than rescuing it; if the cause was the load or the carrier, the existing liquid will not pass without reformulation, so treat it as a loss or reuse it only where clarity and sediment don’t matter to you, and never sell it as a diffuser. If customers already hold bottles from this batch, offer replacements once a passing batch exists. Reed blockage from sediment also shortens a diffuser’s life, so a bottle that looks acceptable may still underperform.
Mogra at CSI, kit prices and the run after a pass
| Item | Need | Buy | ₹ |
|---|---|---|---|
| Your mogra and base | 85 g + 120 g; 435 g | Your own | — |
| Screen jars | 15 | Gold 50 ML, 2 packs (5 spare) | ₹1,652.00 |
| Carrier arm | 80 g | Softness Base 500 ml | ₹1,099.00 |
| Control oil | 20 g | Jasmine 50 g (30 g spare) | ₹230.00 |
| Mixing | 1 | Silicon Measuring Beaker 100 ML | ₹300.00 |
| Stage 1 total | Everything above | ₹3,281.00 | |
| Stage 1 without the Softness arm | Jars + control + beaker | ₹2,182.00 | |
| Stage 2 | 6 bottles, 36 reeds | Gold 120 ML pack + Fiber Reeds Black 50 | ₹1,462.00 |
| Both stages | CSI items only | ₹4,743.00 |
If Softness wins, the screen leaves roughly 420 g of the 500 ml bottle at a worked density of 1.0 g/ml (weigh a measured 100 ml of yours), enough for the 240 g Stage 2 needs.
The purchase step after a pass
Make about ten pilot bottles from the full-size materials you would buy, keep two sealed, and re-read them after 2–4 weeks at room temperature and somewhere warmer and cooler. Then size the run. Worked example: the screen approves mogra at 15% in Softness, and you plan 40 bottles: 600 g of your mogra and 3,400 g of Softness.
| Line | Quantity | Buy | ₹ |
|---|---|---|---|
| Your mogra | 600 g | Your supplier (one lot, retained sample kept) | — |
| Softness Base | 3,400 g | 7 × 500 ml (worked 1.0 g/ml; weigh yours) | ₹7,693.00 |
| Reeds | 240 | 100 + 100 + 50 | ₹2,000.00 |
| Bottles | 40 | four packs of 120 ML | ₹4,248.00 |
| CSI side, Softness route | ₹348.52 a bottle | ₹13,941.00 | |
| CSI side if the fix kept your own base | ₹156.20 a bottle | ₹6,248.00 |
Approve each new lot of mogra with a one-jar screen against your retained sample before it goes into production; that routine is the incoming-QC post at scale. If mogra is one of several florals you are launching, the floral capstone sets per-oil loads and bases, and the three-floral pre-bulk post handles quantity maths for a mixed run.
What to buy
Chosen on page statements, price and stock on 7 October 2026, not on performance: CSI publishes no sediment or stability data. Each card says when not to buy.
| Size | Price | Per ml | Use |
|---|---|---|---|
| 500 ml | ₹1,099.00 | ₹2.20 a ml | screen: 80 g; Stage 2: 240 g; ~420 g left after the screen |
| Size | Price | Per gram | 100 g bottles at 20% | Use |
|---|---|---|---|---|
| 15 gm | ₹103.00 | ₹6.87 | 0 | too small for a 20 g control |
| 50 gm | ₹230.00 | ₹4.60 | 2 | the control jar: 20 g, 30 g spare |
| 100 gm | ₹430.00 | ₹4.30 | 5 | only if you also test it as an oil |
| 500 gm | ₹1,961.00 | ₹3.92 | 25 | not for this test |
| 1 kg | ₹3,923.00 | ₹3.92 | 50 | not for this test |
| Pack | Price | Per bottle | Use |
|---|---|---|---|
| 50 ML Pack of 10 | ₹826.00 | ₹82.60 | screen jars: 2 packs for 15, 5 spare |
| 120 ML Pack of 10 | ₹1,062.00 | ₹106.20 | Stage 2: 6 bottles, 4 spare |
| Size | Price | Note | Use |
|---|---|---|---|
| 100 ML | ₹300.00 | one per oil, dried fully | a dedicated mogra beaker |
| 250 ML (separate listing) | ₹600.00 | larger batches | not needed for 100 g batches |
| Pack | Price | Per reed | Use |
|---|---|---|---|
| Pack of 25 | ₹236.00 | ₹9.44 | too few |
| Pack of 50 | ₹400.00 | ₹8.00 | Stage 2: 36 reeds, 14 spare |
| Pack of 100 | ₹800.00 | ₹8.00 | a run |
| Pack of 500 | ₹4,000.00 | ₹8.00 | same per reed as 50: no saving |
| Size | Price | Per ml | Use |
|---|---|---|---|
| 500 ml | ₹1,099.00 | ₹2.20 a ml | second base arm only if Softness also fails |
CandleMakingSuppliesIndia sells the bottles, bases, reeds, beaker and control oil named here. This page still tells you that our Mogra is out of stock, that a jasmine is not a mogra, that the cause may be your process rather than any product, and that a clean glass beaker you already own will do.
Every CSI price was checked on the live store on 7 October 2026, with stock checked per size; every item offered here is in stock on that date, and the out-of-stock Mogra is named as such and not offered. Page wording is quoted and attributed.
Fragrance behaviour is described as general tendencies, never as the composition of a CSI oil or base; no flash point, solubility, density or composition figure is given. The sediment scale, cool cycle, decision tree and decision rule are in-house methods; the 20% formula, 1.0 g/ml density and 40-bottle run are worked examples. For bulk pricing, GST invoicing, and MSDS and IFRA documentation on request, message us on WhatsApp at +91 7397976926.
Frequently asked questions
- I Made a Jasmine Reed Diffuser with 20% Fragrance Oil and Six Fibre Reeds, but the Room Has Almost No Smell — What Should I Test First?
- My Mogra Fragrance Oil Smells Very Strong in the Bottle but Weak After I Make a Reed Diffuser — Could the Base Be Limiting Diffusion?
- I Made a Rose Reed Diffuser with 25% Fragrance Oil, but the Liquid Turned Cloudy — Should I Test a Lower Load or Different Rose Oil?
- I Made a Mogra Reed Diffuser with Natural Rattan Reeds, but the Scent Is Weak — Should I Try Fibre Reeds Before Increasing Fragrance Oil?
- My Rose Reed Diffuser Becomes Yellow After Three Weeks, but My Lavender Diffuser Stays Clear — How Do I Investigate Fragrance Stability?
- I Made a Floral Reed Diffuser with 30% Fragrance Oil, but It Doesn’t Smell Stronger Than My 20% Version — Could the Higher Load Be Reducing Wicking?
- I Want to Make 100 Jasmine, 100 Rose and 100 Lavender Reed Diffusers — Should I Test Each Fragrance with the Same Base Before Ordering Bulk Oils?
- How Do I Make Strong Floral Reed Diffusers with Jasmine, Mogra, Rose, Lavender and Tuberose Without Assuming One Base and Fragrance Percentage Will Work for Every Oil?
Customer reviews: The six reviews at the top of this page are genuine, published Judge.me reviews left by CSI customers on the product pages named on each card — British Rose Fragrance Oil, Gardenia Fragrance Oil, Gold Reed Diffuser Bottle Pack of 10 (50 ML and 120 ML), Jasmine Fragrance Oil, Lavender Fragrance Oil, Lift Base – Professional Grade Reed & Car Diffuser Base (500 ml). They are general product reviews, not assessments of the reed-diffuser fragrance advice on this page. Names, star ratings, dates and products are as recorded by Judge.me and wording is unedited. "Verified buyer" appears only on reviews Judge.me recorded as verified — snehal Chaudhary, Sooraj R, Sraddha, Judy Roy. The reviews from S.A., Ashwini are published but not recorded as verified, and carry no badge. Reviews below five stars are included as published, not filtered out.
Figures verified 7 October 2026, CSI live pricing: Mogra Fragrance Oil - 100g ₹642.00, out of stock; Jasmine Fragrance Oil 15 gm ₹103.00, 50 gm ₹230.00, 100 gm ₹430.00, 500 gm ₹1,961.00, 1 kg ₹3,923.00; Softness Base 500 ml ₹1,099.00 and Lift Base 500 ml ₹1,099.00 (₹2.20 a ml); Gold Reed Diffuser Bottle Pack of 10, 50 ML ₹826.00 (₹82.60 each), 120 ML ₹1,062.00 (₹106.20 each); Silicon Measuring Beaker 100 ML ₹300.00, 250 ML ₹600.00; Fiber Diffuser Reeds (Black) 25 ₹236.00 (₹9.44 a reed), 50 ₹400.00, 100 ₹800.00, 500 ₹4,000.00 (₹8.00 a reed). Per unit = pack price ÷ units; per ml = price ÷ 500 because the base pages state no density. Totals exclude labour, freight, packaging and GST.
Non-price figures: "after a week" is the reader’s (title). The 20% formula, 100 g fill and six reeds are series defaults assumed because the title gives none. The 40 g jar fill, 14-day screen, cool cycle, 0–3 sediment scale, 21-day Stage 2 and decision rule are in-house methods, not CSI test data. The 1.0 g/ml density and 40-bottle run are worked examples. "Crystal clear", "10-30%", "24-48 hours" and every quoted line are CSI page wording. Diwali, 8 November 2026, is a calendar fact.