I Have DPG, DPM and IPM in My Workshop — Which One Should I Test First as a Reed Diffuser Carrier, and What Properties Should Guide the Choice?
शेयर करना
What properties should guide the choice? Six: solvency (does the oil stay dissolved), viscosity (does it climb the reed), volatility (does it carry fragrance off the tip at the right rate), odour, flammability and cost. Only the first three are tested at the bench; flammability comes from the SDS, never from experiment.
What is the first test? The same oil at 20% (20 g + 80 g carrier) in DPG, DPM, IPM and one ready-made base, three bottles each, 6 fresh fibre reeds, weighed every 2–3 days for 14–30 days, blind sniffs on fixed days. Your rule decides.
What does CSI supply? Not DPG, DPM or IPM. For the test: a base arm, a test oil and reeds, ₹3,291.00 with your own bottles.
- Straight answer: which carrier first
- What DPG, DPM and IPM each do on a reed
- The six properties that should guide the choice
- Why IPM is rarely a good sole carrier
- The cause table: carrier, solubility, oil, reeds, room, process
- The first test: four arms, one oil, three bottles each
- Reading the result, and the purchase step
- What CSI sells for this, and what it doesn't
- What to buy for the test, and what to skip
- Map of this cluster: 8321–8340
- Frequently asked questions
What DPG, DPM and IPM each do on a reed
Your situation, restated: three solvents in the workshop, DPG (dipropylene glycol), DPM (dipropylene glycol methyl ether) and IPM (isopropyl myristate), and the question of which to put through a reed first. No formula is given in the title, so this page uses the series default: 20 g oil + 80 g carrier per 100 g, a 120 ml Gold bottle filled with a labelled 100 g, 6 fibre reeds of 20.3 cm, a closed bedroom as the test room.
A passive reed diffuser needs three things from its carrier. The fragrance must be fully dissolved and stay dissolved. The liquid must be thin enough to climb the reed by capillary action. And the carrier must be volatile enough to carry fragrance off the reed tips into the air, without emptying the bottle long before the life you sell. The three solvents on your shelf sit in different places on those three needs.
DPG is the common benchmark: a low-odour glycol in which fragrances dissolve well, but which evaporates slowly. DPG-heavy diffusers often last a long time and throw weakly, the complaint that runs through the DPG cluster hub. DPM is a glycol ether that is generally more volatile and lower in viscosity than DPG. In a reed, that tends to mean faster rise, more release and a shorter bottle life. IPM is an oily ester with very low volatility. It dissolves many fragrance materials, but on a reed it tends to slow evaporation further. All three statements are tendencies; the actual figures for your lots are in your supplier's SDS and technical data sheet, and we don't quote numbers for them here.
The six properties that should guide the choice
The table gives each property in qualitative terms, hedged, with the bench check that turns it into your own evidence. Where it says "your invoice" or "read the SDS", that is deliberate: those values belong to your supplier and your lot, not to a blog.
| Property | Why it matters on a reed | DPG | DPM | IPM | Bench check |
|---|---|---|---|---|---|
| Solvency | The oil must dissolve fully and stay dissolved, or nothing else matters | Dissolves fragrance well | Generally a good solvent for fragrance | Dissolves many materials | Jar test: 4 g oil + 16 g carrier, room and cool, 7 days |
| Viscosity | Thin enough to climb a fibre reed steadily | Thicker than DPM | Generally thinner than DPG | Oily; check your TDS | Reed rise in 24 h, same reed, same depth |
| Volatility | Carries fragrance off the reed tip without emptying the bottle too fast | Low: slow, long-lasting, often faint | Generally higher than DPG | Very low: tends to slow release further | Grams a day by weight, three bottles |
| Odour | A carrier with its own smell changes every fragrance | Low odour | Check: smell it alone | Check: smell it alone | Blotter, blind, at 1 h and 24 h |
| Flammability | Storage, handling, labelling, shipping | Read the SDS | More volatile: read the SDS with care | Read the SDS | Never at the bench: documents only |
| Cost | Carrier cost per bottle at 80 g | Your invoice | Your invoice | Your invoice | 80 × price per kg ÷ 1,000 |
Two cautions on reading the table. First, volatility is not "more is better". A carrier that leaves fast lifts the room in week one and can leave you with an empty bottle in week three; one that leaves slowly lasts and may never fill the room. The target is the rate your product life needs: 90 g usable over 30–45 days is roughly 2–3 g a day, and your test tells you which carrier lands there with your oil. Second, flammability is a document question, not an experiment. Never "test" it; read section 2 and section 9 of each SDS, and take advice on storage, labelling and shipping for the full formula.
Why IPM is rarely a good sole carrier
IPM earns its place in many cosmetic and perfume formulas as an oily, low-odour solvent. In a passive reed diffuser it has two tendencies that work against you. It is very low in volatility, so it stays on the reed and in the bottle while the fragrance it holds leaves slowly. And it is oily, so reeds can feel greasy and, with some oils, collect residue at the tips. Neither is a certainty for your lot; both are why most makers who try IPM alone are disappointed, and why this cluster treats it as a learning arm and, at most, a minor modifier.
A real formula shows the effect. A CSI customer reviewing an oil described his reed diffuser in his own words:
Read through this page's lens: 60% DPG and 20% IPM make 80% of the bottle low-volatility carrier; only 10% is fragrance, the bottom of most suppliers' ranges; and 10% ethanol leaves early and raises flammability without keeping the room scented for weeks. Low throw is what the tendencies predict. The first test on this page would split it apart: the same oil at 20% in DPG alone, in DPM alone, in IPM alone and in a base. If IPM is the faintest arm, as we would expect, the first change is to take it out, not to add more oil. The IPM-specific checks are in the IPM compatibility post and the IPM-only post.
The cause table: carrier, solubility, oil, reeds, room, process
Rows are grouped, not ranked, and describe what makers commonly report, not CSI test data. Each discriminating check changes one thing.
| Cause | What you would see | Discriminating check | Fix |
|---|---|---|---|
| Carrier volatility | DPG and IPM arms barely lose weight; room faint | Grams a day: DPG vs DPM vs IPM, same oil and reeds | The carrier that lands in your band and passes throw |
| Solubility / stability | Haze or layering in one carrier only | Jar test per carrier, room and cool | That carrier is out at this load; try lower or skip it |
| Viscosity / wicking | One carrier slow to reach the tip | Reed rise in 24 h per carrier | Thinner carrier or partial blend (later, not now) |
| Fragrance load and character | All four arms weak | Second, lighter oil in your best carrier | Change the oil or load, not the carrier |
| Reeds, bottle, fill | Bottles in one arm disagree; oily residue on reeds | Fresh reeds from one pack; identical bottles; fill by weight | Standardise before you compare |
| Room and climate | Results drift between weeks | All arms side by side, same shelf, rotated | Never compare arms run at different times |
| Process | Different stirring, rest or mixing order between arms | Same order (carrier, then oil), same stir, same 24–48 h rest | One written procedure for every arm |
| Measurement | Judging by the liquid line, or open sniffing | Weights every 2–3 days; coded, blind sniffs | Numbers before conclusions |
The fragrance row is the quiet one that saves money. If every carrier, including the ready-made base, gives a faint room with your oil, no carrier swap will fix it: change the oil or the load and come back. That is why the first test uses one oil that spans light and heavy materials, and why a second oil in your best carrier is the first follow-up.
The first test: four arms, one oil, three bottles each
Every arm is a master of three 100 g bottles plus a 20 g jar, mixed by weight: 256 g of carrier and the matching oil. The oil is held at 20% in every arm, the reeds come from one pack, the bottles are identical, and all twelve stand on one shelf, rotated at each reading.
| Arm | Per 100 g bottle | Role | What it answers |
|---|---|---|---|
| A · DPG | 20 g oil + 80 g DPG | control | Your benchmark, measured properly |
| B · DPM | 20 g oil + 80 g DPM | first alternative | Does a more volatile glycol ether lift the room, and at what bottle life? |
| C · IPM | 20 g oil + 80 g IPM | learning arm | How does an oily, slow carrier behave with your oil and reeds? |
| D · CSI base | 20 g oil + 80 g Pure Performance | ready-made arm | Does a black-box base do something your solvents don't? |
For a full 30-day log sheet, with reed-condition and room columns, our live guide on testing reed diffuser performance over 30 days has a template; if any arm turns cloudy, the cloudy-mixing guide covers the diagnosis.
Reading the result, and the purchase step
| Pattern | What you see | What it means | What to do next |
|---|---|---|---|
| 1 | DPM passes; DPG and IPM faint | DPG is too slow for this oil; DPM is the candidate | Confirm DPM against DPG in a second run; then the ratio question |
| 2 | DPM empties too fast; DPG lasts but faint | The answer may sit between them | A DPG/DPM ratio trial, oil held constant |
| 3 | CSI base passes; all three solvents fail | The base does something your solvents don't, with this oil | Second run, base vs your best solvent; ask us for documents |
| 4 | DPG passes your throw threshold | DPG was never the problem with this oil | Keep DPG; look at oil, reeds or room for the products that failed |
| 5 | Everything faint, including the base | The oil or load, not the carrier | Change the oil before buying anything |
| 6 | IPM arm clear, slow and oily on reeds | The expected tendency | Keep IPM out of the sole-carrier role |
| 7 | One arm's bottles disagree widely | Process or measurement | Re-run that arm before reading it |
Patterns 1 and 2 are the most common directions makers report, and they lead to the same next question: what ratio of DPG to DPM, if any, gives the room without emptying the bottle? That is a separate trial with the oil held constant, and it belongs to the solvent-blend cluster. Pattern 3 sends you to a second run of the base against your best solvent, with documents requested before you scale. Pattern 4 is the honest one: if DPG passes with your oil, keep it. The full system for choosing among DPG, DPM, IPM and an Augeo-type base, with weights and a scorecard, is the controlled-tests selection post.
Cost per bottle, then the purchase step
Carrier costs depend on your invoices: 80 g at your price per kg is 80 × price ÷ 1,000. The CSI side is published: Bergamot Amber is ₹112.00 a bottle at 20 g from the 100 gm, ₹108.80 at the 1 kg price; Pure Performance is ₹260.00 for 80 g from the 100g sample and about ₹175.84 for 80 ml from the 500 ML, if your weighed density is near 1.0 g/ml. Compare that with your solvent invoice before you decide a base is worth it; the base-versus-DPM cost post works the break-even.
Say the winner goes into a 50-bottle run: 1,000 g of oil and 4,000 g of carrier. If one of your solvents won, the carrier comes from your own supplier; the CSI side is a Bergamot Amber 1 kg (₹5,437.00), 300 reeds as three packs of 100 (₹2,400.00) and five Gold 120 ML packs (₹5,310.00): ₹13,147.00. If the base arm won, add eight Pure Performance 500 ML (₹8,792.00) for 4,000 ml: ₹21,939.00 in all. Material costs exclude labour, freight, packaging and GST. Against our own interest: buy the base for production only after a second 30-day run agrees with the first.
What CSI sells for this, and what it doesn't
What we do sell for this work: ready-made bases as a comparison arm (Pure Performance 100g is our only sample size; Lift, Depth, Softness and Longevity are 500 ml; the HyperDiffusion Base™ was out of stock on 7 October 2026 and isn't offered), fibre reeds (not rattan), Gold bottles, beakers and fragrance oils. Argued against our own interest: if your DPM arm wins your 30-day test, keep it; we don't sell DPM, and our base doesn't need to be in your formula for your diffusers to work.
Safety, plainly. DPM and many other diffuser carriers and fragrance oils are flammable; a more volatile carrier generally needs more care. Mix and store away from flames, hobs and heaters; ventilate the room; wear gloves and eye protection, and wash skin contact off with soap and water. Keep solvents and finished diffusers out of reach of children and pets, and wipe spills from varnished furniture at once. Check plastic caps and liners against each solvent's SDS. Hazard labelling, storage and courier rules depend on the full formula and where you sell: read every SDS and take advice. This page is not legal advice.
What to buy for the test, and what to skip
Chosen on page statements, price and stock on 7 October 2026, not on performance data; CSI publishes none for its bases or reeds. Each card says when not to buy.
| Size | Price | Unit price | For this test |
|---|---|---|---|
| 100g | ₹325.00 | ₹3.25 a gram | three packs: 256 g needed, 44 g spare |
| 500 ML | ₹1,099.00 | ₹2.20 a ml | after a pass, for production |
| Size | Price | Per gram | Use |
|---|---|---|---|
| 15 gm | ₹105.02 | ₹7.00 | smell check only |
| 50 gm | ₹280.00 | ₹5.60 | two bottles |
| 100 gm | ₹560.00 | ₹5.60 | three packs cover 256 g |
| 500 gm | ₹2,718.00 | ₹5.44 | ₹1,038.00 more than three 100 gm |
| 1 kg | ₹5,437.00 | ₹5.44 | a 50-bottle run (1,000 g) |
| Pack | Price | Per reed | For this test |
|---|---|---|---|
| Pack of 25 | ₹236.00 | ₹9.44 | with the 50 |
| Pack of 50 | ₹400.00 | ₹8.00 | with the 25: 72 needed, 3 spare |
| Pack of 100 | ₹800.00 | ₹8.00 | ₹164.00 more than 50 + 25 |
| Pack of 500 | ₹4,000.00 | ₹8.00 | production only |
| Variant | Price | Each | For this test |
|---|---|---|---|
| 120 ML Pack of 10 | ₹1,062.00 | ₹106.20 each | two packs (₹2,124.00) for 12 bottles |
| 50 ML Pack of 10 | ₹826.00 | ₹82.60 each | only if you sell 50 ml |
| Size | Price | Count | For this test |
|---|---|---|---|
| 100 ML | ₹300.00 | one | mix each 256 g master in two pours, or reuse after cleaning |
| 250 ML | ₹600.00 | one | a whole master in one pour |
Skip for now: a second CSI base arm (one ready-made arm answers "does a black-box base beat my solvents?"; Lift, Depth, Softness and Longevity are family-positioned follow-ups); the CSI HyperDiffusion Base™, out of stock on 7 October 2026; the Isopropyl Alcohol Spray as anything but a bench cleaner; the Room & Linen Spray Base and the Ultrasonic Diffusion Concentrate Base™, which are not reed diffuser bases; and any production pack before a second run.
Map of this cluster: 8321–8340
This hub owns the short answer, the six properties and the four-arm first test. Each sibling takes one carrier question further: DPM (8322–8324), IPM (8325–8327, 8335), Augeo-type comparisons (8328–8333), odour, alcohol and cost (8334, 8337, 8338), and choosing across fragrances and bases (8336, 8339, 8340).
CandleMakingSuppliesIndia sells the base, oil, reeds, bottles and beakers named here. It does not sell DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol, and this page says so. Our base pages publish no composition, density, flash point or SDS in the text we captured, so our base is one arm of your test, and the page tells you to keep your own solvent if it wins.
Every CSI price was checked on 7 October 2026, with stock checked per variant; everything priced here is in stock on that date, and the CSI HyperDiffusion Base™ is out of stock and not offered. Page wording is quoted and attributed to the page; the review is quoted verbatim.
Solvent behaviour is described as general, hedged tendencies with no numeric flash points, viscosities, densities or evaporation rates; those belong to your supplier's SDS and TDS. The arms, thresholds and 50-bottle run are labelled worked examples; nothing here is CSI test data. For bulk pricing, GST invoicing, and MSDS and IFRA documentation for our fragrance oils on request, message us on WhatsApp at +91 7397976926.
Frequently asked questions
- I Want to Make a Reed Diffuser Using DPM Instead of DPG — What Differences in Wicking, Fragrance Solubility and Evaporation Should I Measure?
- My DPM Reed Diffuser Evaporates Faster Than My DPG Version but Doesn’t Smell Much Stronger — What Could Explain the Difference?
- I Want to Use IPM in a Reed Diffuser Formula — How Do I Evaluate Whether It Is Compatible with My Fragrance Oil and Suitable for Reed Wicking?
- Can I Use IPM as the Only Carrier in a Reed Diffuser, or Should I Compare It Against Bases Specifically Designed for Passive Diffusion?
- I Made Three Reed Diffusers Using DPG, DPM and an Augeo-Type Base at 20% Fragrance — How Do I Compare Them Using the Same Bottle and Reeds?
- I Want to Make a Low-Odour Reed Diffuser — How Do I Compare the Carrier Odour of DPG, DPM, IPM and Commercial Bases Before Adding Fragrance?
- I Want to Make a Reed Diffuser Without Ethanol — Which Technical Properties Should I Look for When Comparing DPM and Alcohol-Free Ready-Made Bases?
- How Do I Choose Between DPG, DPM, IPM and an Augeo-Type Reed Diffuser Base Using Controlled Tests for Solubility, Wicking, Throw, Evaporation, Stability and Cost?
- I Made a Reed Diffuser Using 80 g DPG and 20 g Fragrance Oil, but the Reeds Are Wet and the Room Has Almost No Smell — Is DPG the Wrong Base for This Formula?
Customer reviews: The six reviews at the top of this page are genuine, published Judge.me reviews left by CSI customers on the product pages named on each card — Blue Ocean Fragrance Oil, Citrus Lemon Fragrance Oil, Gold Reed Diffuser Bottle Pack of 10 (50 ML and 120 ML), Lift Base – Professional Grade Reed & Car Diffuser Base (500 ml), Room & Linen Spray Base – Fast-Dry, Zero-Residue (500 g), Solar Bloom Fragrance Oil. They are general product reviews, not assessments of the reed-diffuser formulation advice on this page. Names, star ratings, dates and products are as recorded by Judge.me and wording is unedited. "Verified buyer" appears only on reviews Judge.me recorded as verified — Pradeep Kumar Dahiya, Sooraj R, snehal Chaudhary, Thenirvaofficial, Avanthi Cheeli, Yashvi Shah. Reviews below five stars are included as published, not filtered out.
Figures verified 7 October 2026, CSI live pricing: Pure Performance Reed Base Oil 100g ₹325.00, 500 ML ₹1,099.00 (₹2.20 a ml); CSI HyperDiffusion Base™ ₹1,499.00 (out of stock); Bergamot Amber Fragrance Oil 15 gm ₹105.02, 50 gm ₹280.00, 100 gm ₹560.00 (₹5.60 a gram), 500 gm ₹2,718.00 (₹5.44 a gram), 1 kg ₹5,437.00 (₹5.44 a gram); Fiber Diffuser Reeds (Black) 25 ₹236.00 (₹9.44 a reed), 50 ₹400.00, 100 ₹800.00, 500 ₹4,000.00 (₹8.00 a reed from 50 up); Gold Reed Diffuser Bottle Pack of 10, 120 ML ₹1,062.00 (₹106.20 each), 50 ML ₹826.00 (₹82.60 each); Silicon Measuring Beaker 100 ML ₹300.00, 250 ML ₹600.00; Isopropyl Alcohol Spray 150 ML ₹383.00, 1 Litre ₹520.00 (a cleaner). Per unit = pack price ÷ units, two decimals. CSI does not list DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol.
Non-price figures: the reader's three solvents are from the title; the 20 g + 80 g formula, bottle, six reeds, arms, thresholds and 50-bottle run are labelled worked examples. Solvent properties are general tendencies; no numeric viscosities, densities, flash points or evaporation rates are quoted. Base ml are treated as grams only after you weigh 100 ml. "Blend with 10-30% fragrance oil", "No added fixatives", "smooth even wicking" and "10-30% for reed diffusers" are page wording; the review is quoted verbatim. Augeo is a trademark of Solvay; "Augeo-type" describes a solvent class. Costs exclude labour, freight, packaging and GST. Diwali 8 November 2026 and Christmas 25 December 2026 are calendar facts.