I Want to Replace 20 g of DPG with DPM in a 100 g Reed Diffuser Formula — How Do I Calculate the New Ratio While Keeping Fragrance Load Constant?
Share
How do I write it as percentages? Of the total: oil 20.0%, DPG 60.0%, DPM 20.0%. Of the carrier: DPG 75.0%, DPM 25.0%, a 3:1 blend. Scale with the first set; name the blend with the second.
What are the two common mistakes? Swapping 20% of the DPG (16.0 g, a milder change) and adding 20 g DPM on top (120 g, which drops the oil to 16.7%). Either one makes the test answer a different question.
What do I test, and what does CSI supply? DPG control against the 60:20 swap, three 100 g bottles each, weighed every 2–3 days for 14–30 days. CSI supplies the constant parts: Lavender oil, Gold 120 ML bottles, fibre reeds, beakers and a scale; the two-arm kit is ₹3,172.00. CSI sells no DPG or DPM.
- Straight answer: the new ratio
- Your formula, restated
- The arithmetic, and the two traps
- The recipe card: % of total and % of carrier
- Scaling the swap from 100 g to 1 kg
- When the swap seems not to work: cause table
- The by-weight test of the swap
- What to buy for the test, and after it
- Frequently asked questions
Your formula, restated
Your title gives three figures: a 100 g formula, 20 g of DPG to replace, and a fragrance load to keep constant. It does not give the load, so this page assumes the series default, which is also the most common starting point: 20 g fragrance oil + 80 g DPG, a 20% load by weight. If your load is different, the method below still works; only the numbers change, and there is a table for 15% and 25% further down.
The rest of the setup, as you'd test it: the liquid goes into Gold 120 ML bottles at a weighed 100 g each, with six Black fibre reeds (20.3 cm) per bottle, in one room. The oil in the worked example is Lavender Fragrance Oil, chosen because its page gives a diffuser range ("For reed diffusers, use 10-30%") and because its bright top notes show early fade clearly. The reason for the swap is the usual one: an all-DPG diffuser lasts a long time and smells faint. DPG is a low-odour solvent of low volatility, so it dissolves fragrance well but leaves the reed tips slowly. DPM, a glycol ether, is generally more volatile and lower in viscosity. Swapping some DPG for DPM is a way to speed up release without changing the oil. Whether that works for your oil in your room is the test; whether the faster blend actually smells stronger is the question the DPG-to-DPM ratio follow-up takes on.
Neither solvent comes from CSI. We don't sell DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol, so your carrier and its safety data sheet come from your solvent supplier. What follows is the arithmetic, a recipe card, the scale-up and a test plan, with the CSI parts that stay identical across arms.
The arithmetic, and the two traps
The rule is short: oil grams fixed, total grams fixed, grams move only between carriers. Your carrier is 80 g; after the swap, 60 g of it is DPG and 20 g is DPM. Written as a sum: 20 + 60 + 20 = 100. The oil is 20 of 100, which is 20.0%. That is the whole calculation. The trouble starts when the words "replace 20" are read another way, and in a busy workshop they often are.
| Reading | Oil | DPG | DPM | Total | Oil % of total | DPM % of carrier | Verdict |
|---|---|---|---|---|---|---|---|
| Take 20 g out of the DPG | 20.0 | 60.0 | 20.0 | 100.0 | 20.0% | 25.0% | the formula you meant |
| Replace 20% of the DPG | 20.0 | 64.0 | 16.0 | 100.0 | 20.0% | 20.0% | load right, ratio wrong: a different, milder swap |
| Add 20 g DPM on top | 20.0 | 80.0 | 20.0 | 120.0 | 16.7% | 20.0% | load wrong: weaker by dilution, not by solvent |
| Replace 20 g of the whole formula | 16.0 | 64.0 | 20.0 | 100.0 | 16.0% | 23.8% | load wrong: oil was removed too |
Trap 1: "replace 20% of the DPG"
Twenty percent of 80 g is 16.0 g, not 20 g. The result, 20 g oil + 64.0 g DPG + 16.0 g DPM, keeps the load right but makes a milder swap: DPM is only 20.0% of the carrier instead of 25.0%. The batch looks almost identical on the bench, so the error stays hidden until a later batch, mixed correctly, behaves differently. If your notes say "DPM 20%", write beside it of carrier or of total. They are different blends.
Trap 2: adding 20 g DPM to a finished 100 g
This one changes the load. The bottle now holds 120 g with the same 20 g of oil, so the oil falls to 16.7%. If the swap arm then smells weaker, the cause is dilution, not the solvent. If you've already done it, you can rescue the batch for a test: the carrier is now 100 g, so 20% oil means 25.0 g of oil in 125.0 g total. Add 5.0 g of oil. But the carrier is now 80:20 DPG:DPM by grams, a 20.0% DPM blend, not the 3:1 you planned. Record it as what it is.
Converting a batch you have already mixed
You can't take DPG out of a mixed batch. If you want to turn an existing 20 g oil + 80 g DPG into the 3:1 blend, keep the 80 g of DPG as the 75% part. DPM needed: 80 ÷ 3 = 26.67 g. New carrier: 106.67 g. At 20% oil the new total is that carrier ÷ 0.8 = 133.33 g, which needs 26.67 g of oil, so add 6.67 g. It works, but it gives you an odd-sized batch and a second oil addition, which is an extra step that can go wrong. For a test, mix fresh.
The recipe card: % of total and % of carrier
Write the formula two ways and keep both on the card. Percent of total is what you scale and what you compare between formulas. Percent of carrier is how you name the blend ("DPG:DPM 75:25"), and it stays the same when you later change the oil load. Mixing the two up is the source of most diffuser recipe errors that reach production.
| Component | Grams in 100 g | % of total | % of carrier | Source |
|---|---|---|---|---|
| Lavender Fragrance Oil (or your oil) | 20.0 | 20.0% | — | CSI or your supplier |
| DPG (dipropylene glycol) | 60.0 | 60.0% | 75.0% | your solvent supplier |
| DPM (dipropylene glycol methyl ether) | 20.0 | 20.0% | 25.0% | your solvent supplier |
| Total | 100.0 | 100.0% | 100.0% of 80 g carrier | — |
A card is also a record. Add the date, the oil lot, each solvent's supplier and lot number, the scale used and its step, the order of addition, and the actual weights you reached, not just the targets. If the swap passes, this card is your production formula. If a later batch behaves differently, the card is how you'll find out whether the recipe or the batch changed. A full batch record, with traceability, is set out in the 1 kg trial record guide.
When you move on to other loads, keep the carrier ratio and recompute the carrier grams. The DPM share of the carrier is what you're testing; the oil load is a separate variable with its own test.
| Oil load | Oil | Carrier | DPG (75% of carrier) | DPM (25% of carrier) |
|---|---|---|---|---|
| 15% | 15.00 | 85 | 63.75 | 21.25 |
| 20% (your formula) | 20.00 | 80 | 60.00 | 20.00 |
| 25% | 25.00 | 75 | 56.25 | 18.75 |
Note what happens at 25%: DPM falls to 18.75 g and DPG to 56.25 g, because there's less carrier. If you kept 20 g of DPM at 25% oil, the carrier ratio would quietly shift to 55:20, which is a different blend. Use two-decimal grams on the card when your scale reads them; round to your scale's step when you weigh, and record what you actually reached.
Scaling the swap from 100 g to 1 kg
Because the card is in percentages of total, scaling is one multiplication per line. The table gives the four sizes you'll use: one bottle, the master batch for a three-bottle arm, a half-kilo pilot and a 1 kg production batch.
| Batch | Oil (20%) | DPG (60%) | DPM (20%) | Use |
|---|---|---|---|---|
| 100 g | 20.0 g | 60.0 g | 20.0 g | one test bottle |
| 330 g | 66.0 g | 198.0 g | 66.0 g | master batch: three 100 g fills + 30 g retain and losses |
| 500 g | 100.0 g | 300.0 g | 100.0 g | half-kilo pilot |
| 1,000 g | 200.0 g | 600.0 g | 200.0 g | production batch |
Why scale up for the test itself. Small batches magnify weighing error. On a scale that reads whole grams, the reading can be up to half a gram out. Against the 20 g of DPM in a 100 g batch, that is 2.5%. On a 0.1 g scale it is 0.25%. In a 1 kg batch, the same whole-gram scale is out by at most 0.25% on the 200 g of DPM, as good as a 0.1 g scale at 100 g. That is why each arm should be one 330 g master batch, split into three bottles, rather than three separate 100 g mixes. The three bottles then differ only in their reeds and position, not in their recipe.
Tolerance. Set one for each component before you weigh. A workable in-house figure is ±0.5% of the target: ±0.10 g on a 20 g component. If you overshoot, don't pour back; record the actual weight and, if it matters, scale the other two components to match. Pouring solvent back into the stock container is a contamination risk.
Vessels. A 1 kg batch needs a clean, dry vessel holding well over a litre, with room to stir. Glass or stainless steel are the usual choices; whatever you use, check that your solvents do not mark or soften it. Mix until uniform, and stir the same way and for the same time each batch. The oil goes in at 200.0 g, the same 20% as the test, not "about two hundred". When you move beyond 1 kg, the order of addition, mixing time and rest all start to matter more; the 100 g to 10 kg scaling sheet covers that step, and the 500 g fine, 5 kg weak guide covers what goes wrong when batches grow.
When the swap seems not to work: cause table
Suppose you make the swap, test it, and it looks no different from your all-DPG diffuser, or it empties faster but smells no stronger. Before you conclude that DPM doesn't suit your oil, check the causes that have nothing to do with solvent choice. The table keeps them apart.
| Cause | What you'd see | Discriminating check | Fix |
|---|---|---|---|
| Arithmetic: load drifted (DPM added on top, or oil weighed against the carrier) | Weight loss up, smell no stronger or weaker than the DPG control | Recompute oil ÷ total from the batch sheet; it should read 20.0% | Use the recipe card; weigh to the total, not to the carrier |
| Arithmetic: ratio drifted (20% of the DPG swapped, not 20 g) | Swap arm barely differs from control | Batch sheet shows 16.0 g DPM, not 20.0 g | Re-mix by the card; label every beaker |
| Solvent choice really is limiting | g/day rises but the room is still weak at day 14 | Carrier-only bottles (no oil): DPG vs the 60:20 blend, weighed side by side | Try the next ratio step, or a ready-made base arm; don't raise oil |
| Oil character (lavender's bright top fades first) | Day-3 swap arm smells stronger; day-14 arms converge | Score day 3 and day 14 separately | Judge on day 14 to 30, never day 2 |
| Reeds, bottle, fill | One bottle in an arm runs far from its partners | Fill weights and reed counts on the sheet; swap that bottle's reeds | Weighed 100.0 g fills, six reeds from one lot, same bottle |
| Environment | Bottles near a window or fan lose more | Rotate positions every reading; compare rotated means | One shelf, rotated; log temperature and humidity |
| Measurement error (ml instead of grams; coarse scale; open beaker) | DPM arm's first readings jump; totals don't add up | Weigh 100 ml of each solvent; weigh an open beaker of DPM after 10 minutes | Weigh everything, cover beakers, record to your scale's step |
The carrier-only check in row three is the cleanest test of solvent choice, because it takes the oil out of the picture. Fill two bottles with 100 g of plain DPG and two with 75 g DPG + 25 g DPM (the same 3:1 ratio, no oil), add the same reeds, and weigh them on the same days. If the blend loses weight faster, the DPM is doing what it should. If the scented swap arm still smells weak, the limit lies elsewhere: in how the oil leaves the carrier, its load, or the room. The hub, which component is limiting a DPG and DPM blend, shows how to isolate each component in turn.
On safety: a swap that makes the liquid more volatile can change how it should be handled, stored, shipped and labelled. That depends on the full formula, not on one ingredient, so read each solvent's SDS from your supplier, keep the diffuser and its stock away from flames and heat, avoid skin and eye contact while mixing, and keep finished bottles out of reach of children and pets. We can't give legal advice on labelling; the flammability and packaging check sets out what to ask before adding a faster solvent.
The by-weight test of the swap
The test has two arms and one optional third, and changes only the carrier. Arm A is your formula: 20 g oil + 80 g DPG per 100 g. Arm B is the swap: 20 g oil + 60 g DPG + 20 g DPM. Arm C (optional) is the same oil at 20% in Pure Performance Reed Base Oil, a ready-made reference point you didn't make. Each arm is one 330 g master batch, three bottles of 100.0 g, and a 30 g sealed retain. Everything else is the same: oil lot, reed lot and count, bottle pack, room, shelf.
Measuring. Weigh every bottle with the reeds in place, at the same hour, every two to three days, after weighing a sealed check bottle. Grams per day per bottle is (day-0 weight − last weight) ÷ days. Take the mean of each arm's three bottles and the spread between them. The general 30-day method, with reed condition and room temperature, is in the 30-day weight-loss test; use it as written and just add the swap arm.
Sniffing. On days 3, 7, 14 and 30, take each coded bottle alone into a closed second room, wait 15 minutes, and score intensity 1 to 5 from the doorway, plus "smells right" yes or no. Two or three people if you can; codes kept by someone else. This is an in-house method, not a standard. Stability. At every reading, look for haze, layers, sediment or a colour change in the bottles and the retain. A swap that clouds has failed whatever it smells like; the cloudy two-carrier blend guide shows how to find which ingredient is responsible.
Your pass rule, written before day 0
This is an example to adapt, not a standard. Arm B passes if, over 14 to 30 days: (1) the bottles and the retain stay clear, with no layer or sediment; (2) its mean g/day sits inside the life you promise, say 100 g over 45 to 90 days, which is 1.11 to 2.22 g/day; (3) its median day-14 sniff score is at least one point above Arm A's; (4) its three bottles agree within 15% of their mean. Pass all four and the swap is your formula. Fail (1) and the swap is out. Pass (1) and (2) but not (3), and you have a faster diffuser that isn't stronger: try the next ratio step, as in the three-ratio experiment, rather than adding oil.
What to buy for the test, and after it
Chosen on page statements, price and stock on 7 October 2026, not on performance: CSI publishes no diffusion data for any product. Each card is a part that stays identical across arms, a tool for weighing, or the optional control.
| Size | Price | Per gram | 100 g bottles at 20% | In this test |
|---|---|---|---|---|
| 15 gm | ₹105.02 | ₹7.00 | 0 | smell check only |
| 50 gm | ₹270.00 | ₹5.40 | 2 | top-up for the third arm |
| 100 gm | ₹540.00 | ₹5.40 | 5 | one arm is 66 g; two 100s + one 50 cover three arms |
| 500 gm | ₹2,620.00 | ₹5.24 | 25 | only once the swap has passed |
| 1 kg | ₹5,221.00 | ₹5.22 | 50 | production: ₹19.00 less than two 500 gm |
| Item | Price | Use |
|---|---|---|
| Candle Making Weighing Scale | ₹354.00 | batching; check its step before use |
| Item | Price | In this test |
|---|---|---|
| Silicon Measuring Beaker 100 ML | ₹300.00 | oil |
| Silicon Measuring Beaker 250 ML | ₹600.00 | DPG / DPM for 100 g batches |
| Size | Price | Per bottle | In this test |
|---|---|---|---|
| 50 ML Pack of 10 | ₹826.00 | ₹82.60 | not for 100 g fills |
| 120 ML Pack of 10 | ₹1,062.00 | ₹106.20 | 9 test bottles + 1 check bottle |
| Pack | Price | Per reed | In this test |
|---|---|---|---|
| Pack of 25 | ₹236.00 | ₹9.44 | top-up |
| Pack of 50 | ₹400.00 | ₹8.00 | two arms (36 reeds) |
| Pack of 100 | ₹800.00 | ₹8.00 | production |
| Pack of 500 | ₹4,000.00 | ₹8.00 | no saving per reed |
| Size | Price | Unit price | In this test |
|---|---|---|---|
| 100g | ₹325.00 | ₹3.25 a gram | one bottle only |
| 500 ML | ₹1,099.00 | ₹2.20 a ml | control arm, three bottles |
Test quantities. Each arm's master batch takes 66 g of oil, so two arms need 132 g: a 100 gm and a 50 gm (₹810.00), leaving 18 g. Three arms need 198 g: two 100 gm and one 50 gm (₹1,350.00), leaving 52 g. Reeds: 36 for two arms, 54 for three. The three-arm kit with Pure Performance is ₹5,047.00. Per test bottle, the CSI parts come to ₹262.20: oil ₹108.00, bottle ₹106.20, reeds ₹48.00. Add your own carrier. Costs exclude labour, freight, packaging and GST.
After a pass: five 1 kg batches. Five batches make 5,000 g: 4,800 g in 48 bottles at 100 g, and 200 g for retains and losses. Oil: 1,000 g, one 1 kg pack at ₹5,221.00 (₹19.00 less than two 500 gm packs at ₹5,240.00). Solvents, from your supplier: 3,000 g DPG and 1,000 g DPM. Bottles: five packs of 120 ML, ₹5,310.00, two spare. Reeds: 288 at six a bottle, three packs of 100, ₹2,400.00, 12 spare; a 500-pack would tie up ₹1,600.00 more for no saving per reed. CSI items total ₹12,931.00, or ₹269.40 a filled bottle before your solvents. Changing the oil lot, reed lot or bottle after the test makes it a new test.
Skip: the CSI HyperDiffusion Base (out of stock on 7 October 2026), and the Isopropyl Alcohol Spray, which is a cleaning product, not a diffuser ingredient. Don't buy a 1 kg of oil until the swap has passed and been repeated once on a fresh batch.
CandleMakingSuppliesIndia sells fragrance oils, reed diffuser bases, fibre reeds, bottles and weighing tools. It does not sell DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol. This page still tells you to skip our base if you only want DPG against the swap, that our reed packs save nothing above 50, and that our base pages publish no composition, density, flash point or SDS in the text we captured.
Every CSI price was checked on the live store on 7 October 2026, with stock checked per size. Every product and size offered here was in stock on that date; the CSI HyperDiffusion Base is out of stock and not offered. Page wording is quoted and attributed.
The arithmetic is exact. The 20% starting load, the test life window, the ±0.5% tolerance, the sniff method and the pass rule are labelled worked examples and judgement, not CSI test data. For bulk pricing, GST invoicing, and MSDS and IFRA documentation for our fragrance oils on request, message us on WhatsApp at +91 7397976926.
Frequently asked questions
- I Mixed DPG and DPM to Make My Own Reed Diffuser Base, but the Finished Diffuser Still Has Weak Throw — How Do I Determine Which Component Is Limiting Performance?
- I Made a Reed Diffuser with 20% Fragrance Oil and a Blend of Two Carriers, but It Turned Cloudy — How Do I Identify the Incompatible Ingredient?
- My Reed Diffuser Formula Is Clear with 10% Fragrance Oil but Separates at 20% — How Do I Determine Whether the Solvent Blend Has Reached Its Compatibility Limit?
- I Changed My DPG-to-DPM Ratio, and the Diffuser Started Evaporating Faster — How Do I Check Whether Fragrance Throw Improved as Well?
- I Want to Test Three Carrier Ratios with One Jasmine Fragrance — How Do I Design the Experiment So Fragrance Percentage and Reed Count Remain Identical?
- I Want to Make a 1 Kg Reed Diffuser Base Trial from Multiple Solvents — How Do I Record Exact Ingredient Weights and Maintain Batch Traceability?
- I Have Made Five Different Solvent Blends, but I Cannot Tell Which One Performs Best — What Measurements Should I Record During a 30-Day Test?
- How Do I Develop My Own Reed Diffuser Base from Compatible Solvents, Test It with Several Fragrances, Measure Diffusion and Stability, and Decide Whether It Is Better Than Buying a Ready-Made Base?
Customer reviews: The six reviews at the top of this page are genuine, published Judge.me reviews left by CSI customers on the product pages named on each card — Gold Reed Diffuser Bottle Pack of 10 (50 ML and 120 ML), Lavender Fragrance Oil, Lift Base – Professional Grade Reed & Car Diffuser Base (500 ml), Room & Linen Spray Base – Fast-Dry, Zero-Residue (500 g). They are general product reviews, not assessments of the reed-diffuser formulation advice on this page. Names, star ratings, dates and products are as recorded by Judge.me and wording is unedited. "Verified buyer" appears only on reviews Judge.me recorded as verified — Akansha, Tina Raha, Priyanka Purohit, Sooraj R, snehal Chaudhary, Thenirvaofficial. Reviews below five stars are included as published, not filtered out.
Figures verified 7 October 2026, CSI live pricing: Lavender Fragrance Oil 15 gm ₹105.02, 50 gm ₹270.00, 100 gm ₹540.00 (₹5.40 a gram), 500 gm ₹2,620.00, 1 kg ₹5,221.00 (₹5.22 a gram); Pure Performance Reed Base Oil 100g ₹325.00, 500 ML ₹1,099.00 (₹2.20 a ml); Gold Reed Diffuser Bottle 50 ML pack of 10 ₹826.00, 120 ML pack of 10 ₹1,062.00 (₹106.20 each); Fiber Diffuser Reeds (Black) 25 ₹236.00, 50 ₹400.00, 100 ₹800.00, 500 ₹4,000.00; Silicon Measuring Beaker 100 ML ₹300.00, 250 ML ₹600.00; Candle Making Weighing Scale ₹354.00. All in stock on 7 October 2026; the CSI HyperDiffusion Base is out of stock. Per gram, per ml and per item = price ÷ units, two decimals.
Non-price figures: the reader's title gives a 100 g formula and a 20 g DPG swap; the 20 g oil + 80 g DPG start is the series default, labelled as assumed. All formula arithmetic is exact. The 330 g master batch, the ±0.5% tolerance, the 45–90-day life window, the 15% spread limit, the sniff method and the pass rule are labelled in-house examples. Three bottles per arm, 100 g fills and six 20.3 cm fibre reeds are the series method. No density, flash point, viscosity or evaporation figure is given for any material; read your supplier's SDS. Diwali 8 November 2026 and Christmas 25 December 2026 are calendar facts. Costs are materials only and exclude labour, freight, packaging and GST.