I Made a Reed Diffuser with 15% Fragrance Oil and DPG, and the Liquid Is Clear but Very Slow to Wick — How Do I Determine Whether Viscosity Is the Problem?
शेयर करना
How do I check without a viscometer? Stand white fibre reeds in four liquids (DPG alone, your DPG + 15% oil, a CSI base alone, the base + 15% oil). Mark the wet front at 1, 4 and 24 hours, blot the tips with paper, and weigh how much liquid each reed has taken up in 24 hours.
How do I read it? If DPG alone is slow, the carrier is the limit. If only DPG + oil is slow, your oil is thickening it. If every front reaches the tip but the bottle barely loses weight, the problem is evaporation, not viscosity.
What does it cost? Stage 1: Pure Performance 100g ₹325.00 + White reeds 50 ₹450.00 = ₹775.00. Both stages, with a 500 ML base, black reeds and a pack of Gold bottles: ₹3,011.00. CSI doesn't sell DPG.
- Straight answer: is it viscosity?
- Slow rise or slow release: two different problems
- The cause table: carrier, oil, evaporation, reeds, depth, temperature
- Stage 1: the four-liquid wicking test
- A rough thickness check, and its limits
- Stage 2: what to change, and the diffuser test
- What to buy for this test, and what to skip
- Frequently asked questions
Slow rise or slow release: two different problems
Your formula, restated: 15 g fragrance oil + 85 g DPG per 100 g (15% oil by weight), clear, in a reed bottle, and the liquid is "very slow to wick". You haven't given the bottle or reeds, so this page assumes a 120 ml Gold bottle with a labelled 100 g fill and 5 fibre reeds, which are worked examples. Clear is good news: the oil is dissolved. It doesn't tell you how the liquid moves.
A reed diffuser needs three things. The fragrance must be dissolved and stable in the carrier. The liquid must be thin enough to climb the reed by capillary action. And the carrier must be volatile enough to leave the tips and carry fragrance into the room. "Slow to wick" usually describes a failure of the second, but people often say it when the third is the problem. If the reeds stay dark to the tip and the room is faint, the pump is working and the chimney is slow. DPG is a common, low-odour solvent that holds fragrance well, is thicker than many alternatives and evaporates slowly. So in a DPG formula either half can be the bottleneck.
Your 15% matters too. Fragrance oils vary widely: some are light and thin, others carry heavy, viscous materials (resins, vanilla-type notes, some woods and musks). The same 15% of a heavy oil can slow a carrier that a light oil barely affects. That is why the test below includes the carrier without the oil. It is the only way to see how much of the slowness the oil adds.
The cause table: carrier, oil, evaporation, reeds, depth, temperature
Rows are grouped, not ranked; the evidence column is what you would commonly see, not CSI test data. The first two rows are the viscosity rows. The third row is the one most often mistaken for them.
| Cause | What you would see | Discriminating check | Fix |
|---|---|---|---|
| Carrier viscosity (DPG) | DPG alone climbs slowly too; tips dry for hours | Liquid 1 (DPG alone) vs liquid 3 (base alone): front height and 24 h gain | Lower-viscosity partner for part of the DPG, or a different base |
| Oil raises viscosity | DPG alone fine; DPG + oil clearly slower | Liquid 1 vs liquid 2; a lighter oil at the same 15% | Lower load (10%) or a different oil; see 8317 for vanilla-heavy oils |
| Slow evaporation, not slow rise | Front reaches the tip within hours; bottle barely loses weight | Paper blot at the tip vs assembled-diffuser weight loss | A volatility fix, not a viscosity fix: 8302 and 8306 |
| Solubility / micro-haze | Looks clear, but a faint film or tip residue builds | Clear jar under a torch beam; warm/cool storage 2–4 weeks | Different carrier ratio or oil; residue problems are 8312 |
| Reeds | One batch of reeds slow in every liquid | Same liquid, reeds from a fresh pack; white vs black | Fresh reeds; same pack for every arm |
| Bottle, neck and fill depth | Low fill: liquid has further to climb | Same liquid at two fill depths | Fill by weight to one labelled level |
| Temperature | Slower in a cold room or winter | Repeat liquid 2 in a warmer room; log temperature | Test at the temperature the product lives in |
| Process | Freshly mixed; not rested; stirred unevenly | Rest 24–48 h and retest the same liquid | Weigh, stir until clear, rest |
| Measurement error | "Slow" judged by sniffing a tip on day 1 | Timed front marks, blot, 24 h weight gain | Numbers, not impressions |
The four-liquid test is built to split the first three rows at once. Liquid 1 against liquid 2 shows the oil's effect. Liquid 1 against liquid 3 shows the carrier's. The blot and the diffuser weight log separate rise from release. Sticky, varnished reeds after weeks of use are a residue problem rather than a speed problem, and that is the sticky coffee-reeds post. Vanilla-heavy oils that visibly thicken DPG are the thick vanilla post.
Stage 1: the four-liquid wicking test
Make four liquids of 40 g each, by weight, on the same day. Use four identical jars or bottles at the same fill depth: depth sets how far the liquid must climb, so it must match.
| Liquid | Recipe (40 g) | Compared with | What the difference tells you |
|---|---|---|---|
| 1 · DPG alone | 40 g DPG | Liquid 3 | How fast your carrier climbs, without oil |
| 2 · your formula | 6 g oil + 34 g DPG | Liquid 1 | How much your oil slows DPG |
| 3 · CSI base alone | 40 g Pure Performance | Liquid 1 | Whether a ready-made base climbs faster than DPG |
| 4 · base + your oil | 6 g oil + 34 g Pure Performance | Liquid 2 | Whether the base keeps your oil moving better |
Totals: 74 g of DPG, 74 g of Pure Performance (one 100g pack, with some spare) and 12 g of your oil. Rest all four for 24 hours, covered, before the reeds go in.
Reading it. In the diagram's illustration, DPG alone gains 0.40 g per reed in 24 hours, DPG + oil 0.32 g (20% less), the base alone 0.55 g and the base + oil 0.50 g. That pattern would say the oil slows DPG noticeably and the base carries your oil more readily. Illustrative, not CSI data. Possible readings of your own numbers:
| Pattern | What it means | Next step |
|---|---|---|
| 1 slow, 2 slower, 3 and 4 faster | DPG is a rise limit, and your oil adds to it | Stage 2 arms B and C |
| 1 fast, 2 much slower | Your oil thickens DPG; the carrier alone is fine | Test 10% oil or a lighter oil before changing carrier |
| All four reach the tip in hours | Not a rise problem | It's release: weigh the diffuser, see 8302 / 8306 |
| 2 and 4 both slow, 1 and 3 fast | The oil slows any carrier | Oil choice or a lower load; a new base won't fix it |
| Big spread within a liquid | Reed-to-reed variation is swamping the test | More reeds per point, or a fresh pack |
A rough thickness check, and its limits
If you want a second, cruder signal, time how long the same weight of each liquid takes to drain by gravity. Use four identical new disposable plastic syringes (10 ml, no needle) or identical droppers, held vertically over a beaker. Fill each with liquid, release, and time the flow until it breaks into drops. Do three repeats per liquid, at one room temperature, in one session.
Three cautions. It's relative. "Liquid 2 takes longer than liquid 1" is all it can tell you; it gives no figure to compare with a supplier's data sheet, and we don't publish one for our bases. Temperature moves it a lot. Viscous liquids thin noticeably when warm, which is one reason diffusers often run faster in Indian summer (roughly April–June) than in winter (roughly December–February). Never compare a liquid timed at noon with one timed at night. Capillary rise isn't only viscosity. Surface tension and how the liquid wets the fibre matter too, so a liquid can drain slowly and still climb a reed acceptably. The reed test above decides; the drain test only supports it. If you need actual viscosity values for a solvent you use, ask that supplier for the TDS; for CSI bases, ask us on WhatsApp what we can obtain.
Stage 2: what to change, and the diffuser test
An uptake test shows the bottleneck. It doesn't prove a better product: a thinner liquid can climb faster and still throw weakly, or empty the bottle too quickly. So every change goes into a finished-diffuser test with three bottles per arm.
| Arm | Per 100 g bottle | Run it when stage 1 showed | Watch for |
|---|---|---|---|
| A · control | 15 g oil + 85 g DPG | Always | Your current rate and sniff score |
| B · thinner carrier | 15 g oil + 64 g DPG + 21 g of a documented lower-viscosity co-solvent | DPG alone slow (pattern 1) | Clarity, solvent odour, SDS changes |
| C · CSI base | 15 g oil + 85 g Pure Performance | Base climbed faster (pattern 1) | Faster emptying; life still acceptable |
| (alt) · lower load | 10 g oil + 90 g DPG | Oil thickens DPG (pattern 2) | Throw per gram of oil; run it instead of B |
For arm B, DPM, a glycol ether, is generally lower in viscosity and more volatile than DPG and is a common candidate; Augeo-type glycerol-ketal solvents are another option (Augeo is a trademark of another company). We don't sell either, and we quote no viscosity figures for any of them. Read the co-solvent's SDS first: a more volatile partner can change flammability and labelling, and how to check that is in the DPG-only post. What to measure when you swap DPG for DPM is the DPM measurement post.
Bill of materials and the purchase step
Stage 2 uses 9 bottles, 135 g of your oil and 255 g of Pure Performance. Both stages together need 329 g of base. One 500 ML (₹1,099.00) is cheaper than four 100g packs (₹1,300.00) by ₹201.00, provided 500 ml weighs at least 329 g, which any density above about 0.66 g a ml covers. Weigh 100 ml once to confirm. Add a pack of 50 black reeds (₹400.00) for 45 reeds and one Gold 120 ML pack (₹1,062.00). The CSI side of both stages is ₹3,011.00, or ₹1,949.00 with your own identical bottles. After a pass, size production from your own weighed g/day and fill. For quantities, see how much base to buy for 100 bottles at 20% load; CSI lists no base pack above 500 ml, so ask on WhatsApp. Costs exclude your oil, labour, freight, packaging and GST.
What to buy for this test, and what to skip
Chosen for this test on page statements, price and stock on 7 October 2026, not on performance data. CSI publishes none for its bases or reeds. Each card says when not to buy.
| Pack | Price | Per reed | For this test |
|---|---|---|---|
| Pack of 25 | ₹265.00 | ₹10.60 | too few for the 36-reed uptake test |
| Pack of 50 | ₹450.00 | ₹9.00 | 36 reeds for stage 1, 14 spare |
| Pack of 100 | ₹900.00 | ₹9.00 | same per reed as 50 |
| Pack of 500 | ₹4,500.00 | ₹9.00 | same per reed: no saving |
| Pack | Price | Per reed | For this test |
|---|---|---|---|
| Pack of 25 | ₹236.00 | ₹9.44 | too few for nine bottles |
| Pack of 50 | ₹400.00 | ₹8.00 | stage 2: 45 reeds for 9 bottles |
| Pack of 100 | ₹800.00 | ₹8.00 | production |
| Pack of 500 | ₹4,000.00 | ₹8.00 | same per reed as 50 |
| Size | Price | Unit price | For this test |
|---|---|---|---|
| 500 ML | ₹1,099.00 | ₹2.20 a ml | both stages need 329 g: cheaper than four 100g by ₹201.00 |
| 100g | ₹325.00 | ₹3.25 a gram | stage 1 alone needs 74 g: one pack |
| Listing | Price | — | Check first |
|---|---|---|---|
| Default Title | ₹354.00 | — | resolution not stated: a reed gains well under a gram, so check it reads 0.01 g or use a jewellery scale |
| Listing | Price | — | Use |
|---|---|---|---|
| 100 ML | ₹300.00 | — | mixing the four 40 g test liquids by weight |
| 250 ML (separate listing) | ₹600.00 | — | stage 2 masters of 300 g |
Skip for now: Depth or Longevity Base as a "thinner" option: their pages say nothing about viscosity, and Depth's page says it "Slows evaporation", the opposite direction to a release problem. Also skip the CSI HyperDiffusion Base™ (out of stock on 7 October 2026), the Isopropyl Alcohol Spray (a cleaner, never a diffuser ingredient or thinner) and any 500-reed pack before stage 2 has passed.
CandleMakingSuppliesIndia sells the bases, fibre reeds, bottles, beakers and scale named here. It does not sell DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol, and this page says so. Our base pages publish no composition, viscosity, density, flash point or SDS in the text we captured, so this page gives a way to compare liquids without numbers rather than inventing any.
Every CSI price was checked on 7 October 2026, with stock checked per variant; everything priced here is in stock on that date, and the CSI HyperDiffusion Base™ is out of stock and not offered. Page wording is quoted and attributed to the page.
The reed gains, front heights and diagram are illustrative, not CSI test data. The 40 g test liquids, 100 g fills, 5 reeds, arm recipes and decision thresholds are labelled worked examples; the rule is yours. For bulk pricing, GST invoicing, and MSDS and IFRA documentation for our fragrance oils on request, message us on WhatsApp at +91 7397976926.
Frequently asked questions
- I Made a Reed Diffuser Using 80 g DPG and 20 g Fragrance Oil, but the Reeds Are Wet and the Room Has Almost No Smell — Is DPG the Wrong Base for This Formula?
- I Used DPG as My Only Reed Diffuser Base, and the Liquid Level Has Barely Dropped After Two Weeks — Should I Switch to a More Volatile Carrier?
- I Made a 120 ml Reed Diffuser with DPG and Six Fibre Reeds, but Only the Reeds Smell Strong — Could the Carrier Be Evaporating Too Slowly?
- I Mixed 20 g Coffee Fragrance Oil with 80 g DPG, but the Fibre Reeds Have Become Sticky — Could the Fragrance Composition Be Restricting Wicking?
- My DPG-Based Reed Diffuser Smells Strong Only When I Flip the Reeds — How Do I Determine Whether the Base or Reed Material Is Responsible?
- My DPG Reed Diffuser Has Almost No Weight Loss After Ten Days — How Do I Run a Controlled Evaporation Test to Compare Alternative Bases?
- My Vanilla Fragrance Oil Makes My DPG-Based Diffuser Thick and Slow — Should I Test a Lower Fragrance Percentage or a Different Carrier?
- I Want to Stop Guessing with DPG Reed Diffuser Formulas — How Do I Compare Solubility, Wicking, Evaporation, Throw and Cost Before Choosing My Next Base?
Customer reviews: The six reviews at the top of this page are genuine, published Judge.me reviews left by CSI customers on the product pages named on each card — Apple Cinnamon Fragrance Oil, Bamboo Stirring Sticks for Mixing Wax, Gold Reed Diffuser Bottle Pack of 10 (50 ML and 120 ML), Jasmine Fragrance Oil, Lift Base – Professional Grade Reed & Car Diffuser Base (500 ml), Room & Linen Spray Base – Fast-Dry, Zero-Residue (500 g). They are general product reviews, not assessments of the reed-diffuser formulation advice on this page. Names, star ratings, dates and products are as recorded by Judge.me and wording is unedited. "Verified buyer" appears only on reviews Judge.me recorded as verified — Sooraj R, snehal Chaudhary, Thenirvaofficial. The reviews from Lalitha Jagan, S.A., Lalitha Jagan are published but not recorded as verified, and carry no badge. Reviews below five stars are included as published, not filtered out.
Figures verified 7 October 2026, CSI live pricing: Fiber Diffuser Reeds (White) 25 ₹265.00 (₹10.60 a reed), 50 ₹450.00, 100 ₹900.00, 500 ₹4,500.00 (₹9.00 a reed from 50 up); Fiber Diffuser Reeds (Black) 25 ₹236.00 (₹9.44 a reed), 50 ₹400.00, 100 ₹800.00, 500 ₹4,000.00 (₹8.00 a reed from 50 up); Pure Performance Reed Base Oil 100g ₹325.00 (₹3.25 a gram), 500 ML ₹1,099.00 (₹2.20 a ml); Depth and Longevity Base 500 ml ₹1,099.00 and ₹1,296.00; CSI HyperDiffusion Base™ ₹1,499.00 (out of stock); Gold Reed Diffuser Bottle Pack of 10, 120 ML ₹1,062.00 (₹106.20 each); Candle Making Weighing Scale ₹354.00; Silicon Measuring Beaker 100 ML ₹300.00, 250 ML ₹600.00; Isopropyl Alcohol Spray 150 ML ₹383.00 (a cleaner, named only to rule it out). Per unit = pack price ÷ units, two decimals. CSI does not list DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol.
Non-price figures: "15% fragrance oil", "DPG", "clear" and "very slow to wick" are the reader's (title). The 40 g test liquids, 3 reeds per time point, 1/4/24 h schedule, 100 g fills, 5 reeds, arm recipes and decision thresholds are labelled worked examples. The reed gains and front heights are illustrative, not CSI test data. No viscosity, density, flash point or evaporation figure is quoted for any material. "Allow 1-2 hours for full absorption", "smooth even wicking", "High-performance capillary action for stronger throw", "Slows evaporation" and "Blend with 10-30% fragrance oil" are page wording. Costs exclude labour, freight, packaging and GST. Christmas 25 December 2026 is a calendar fact.