I Used DPG as My Only Reed Diffuser Base, and the Liquid Level Has Barely Dropped After Two Weeks — Should I Switch to a More Volatile Carrier?
Share
What rate should I want? Your own: usable fill ÷ target days. Worked example: 90 g usable over 45–90 days is 1.00–2.00 g a day. An illustrative 4.2 g lost in 14 days is 0.30 g a day, about 5.0 times below a 60-day target.
What do I test? Same oil at 20%, carrier changed in steps: DPG as 100%, 75% and 50% of the carrier, the rest a compatible, more volatile co-solvent you already use and have an SDS for, plus a CSI ready-made base arm. Three bottles each, weighed every 2–3 days for 14–30 days, with blind sniffs.
What does it cost at CSI? Pure Performance 100g ×3 ₹975.00 + fibre reeds 50 + 25 ₹636.00 + two Gold 120 ML packs ₹2,124.00 = ₹3,735.00. With your own identical bottles: ₹1,611.00. CSI does not sell DPG or any co-solvent: those are yours.
- Straight answer: switch carrier or not?
- Turning "barely dropped" into grams a day
- What rate you actually need: your target band
- The cause table: carrier, oil, reeds, bottle, room, process, measurement
- Before a volatile co-solvent goes in: the flammability check
- The replacement ladder: four arms, twelve bottles
- Reading the result, and the purchase step
- What to buy for this test, and what to skip
- Frequently asked questions
Turning "barely dropped" into grams a day
Your situation, restated: fragrance oil and DPG, nothing else in the carrier, filled into a reed bottle, and after 14 days the liquid line has hardly moved. You haven't told us the oil, the percentage or the reed count, so this page uses a worked example, labelled as such: 20 g oil + 80 g DPG = 100 g (20% by weight), in a 120 ml Gold bottle with 5 fibre reeds. Swap in your own figures; the method doesn't change.
Three things make the level line a poor gauge. Reeds drink first. In the first day or two the reeds soak up liquid that hasn't left the system, so a level that falls early and then stalls can mean no evaporation at all. Bottle shoulders distort. Near the neck a few grams make a visible change; lower down in the wide body, the same grams barely move the line. Volume isn't weight. You formulated in grams (or should have), and the density of your liquid is not on any label we know of.
So weigh the whole assembled diffuser, bottle, liquid and reeds together, at the same time of day. Liquid moving from bottle into reed doesn't change that weight. Only what leaves into the air does. If you never weighed day 0, start now: weigh today, then every 2–3 days, and work from the slope. Worked example, illustrative: an assembled diffuser that has lost 4.2 g in 14 days is releasing 0.30 g a day. At that rate 90 g of usable liquid would last about 300 days. That isn't long life. It is a product that is barely working.
What rate you actually need: your target band
Nobody can tell you the "correct" g/day for a reed diffuser, because it depends on the life you promise. Work it out from your own product. Usable fill is what the reeds can actually pull out. Some liquid usually stays below the reach of the reeds or is held in them at the end: our worked example allows 10 g, so 90 g of a 100 g fill is usable. Target life is the number of days you'd be comfortable printing. Divide one by the other.
| Target life | Needed rate | Grams lost by day 14 | Your illustrative 0.30 g/day against it |
|---|---|---|---|
| 30 days | 3.00 g/day | 42.0 g | Ten times too slow |
| 45 days | 2.00 g/day | 28.0 g | About 6.7 times too slow |
| 60 days | 1.50 g/day | 21.0 g | 5.0 times too slow |
| 90 days | 1.00 g/day | 14.0 g | About 3.3 times too slow |
For this page the band is 45–90 days: 1.00–2.00 g a day, the shaded wedge in the diagram. A 60-day diffuser would have lost about 21.0 g by your day 14, and nobody would describe that as "barely dropped". A diffuser that loses 4.2 g has stalled, whichever band you choose.
Two cautions keep this honest. A rate inside the band is necessary, not sufficient. A carrier can evaporate quickly and still carry little fragrance with it, which is why every arm also gets a blind sniff. The band is not the whole life-versus-throw trade-off. If your diffuser already lasts for months and the question is where to set the balance, that is the three-month balance post. This page is narrower: your rate is far below any sensible band, so what do you change?
The cause table: carrier, oil, reeds, bottle, room, process, measurement
A stalled DPG diffuser usually points at the carrier, but the table separates the other things that produce the same symptom. Rows are grouped, not ranked, and the evidence column is what you'd commonly see, not CSI test data.
| Cause | What you would see | Discriminating check | Fix |
|---|---|---|---|
| Carrier volatility · DPG alone is slow | Steady but tiny weight loss; reeds wet to the tip; weak room scent; nothing wrong in the bottle | Arm A against arms B, C, D: same oil, same reeds; only the carrier changes | Partial replacement (arms B, C) or a different base (D) |
| Carrier viscosity · slow rise | Reed tips stay pale or dry for days; liquid climbs slowly | Time for the liquid to reach the tip; reed weight gain over 24 hours (the viscosity post) | Lower-viscosity co-solvent or base; check oil load |
| Solubility / stability | Haze, layering, droplets, film on the surface | Clear jar of the same blend at room, warm and cool for 2–4 weeks | A carrier that holds the oil clear; if it never clears, it is not this post's problem |
| Fragrance composition and load | Heavy base-note oil; level barely moves even in a fast base | Same carrier with a lighter oil at the same % | Oil choice, not carrier; or a lower % (load ladder within 10–30%) |
| Reeds | Clogged, sticky or varnished reeds; old rattan | Fresh reeds into the same bottle mid-test | Fresh fibre reeds; same count in every arm |
| Bottle and neck | Very narrow neck, tightly packed reeds; or a cap left on | Same liquid, same reeds, a different identical-volume bottle | One bottle type for the whole test |
| Room and climate | Cool, still room; AC; winter | Log temperature and humidity at every weighing; all arms side by side | Test where the product will live; compare arms only in the same room |
| Process | Mixed by volume; no rest; stirred unevenly | Remake one arm by weight with a 24–48 hour rest | Formulate by weight; one master batch per arm |
| Measurement error | "Barely dropped" judged by eye at the shoulder of the bottle | Weigh the assembled diffuser (bottle + liquid + reeds) on day 0 and every 2–3 days | Grams a day, never the level line |
Rule out the last row before anything else. If you haven't weighed, you don't yet have a symptom, only an impression. Then the ladder below tests the first row directly, and the controls (same reeds, bottle, room and oil) hold rows four to seven still.
Why DPG behaves like this. Passive reed diffusion needs three things: the fragrance fully dissolved and stable in the carrier, a liquid thin enough to climb the reed, and a carrier volatile enough to leave the reed tips and take fragrance with it, without emptying the bottle too fast. DPG (dipropylene glycol) is a common, low-odour solvent that is very good at the first, adequate at the second, and slow at the third. That is why DPG-heavy formulas often last a long time and throw weakly. A real customer formula shows the same pattern with an even slower partner, IPM, in it. Pradeep Kumar Dahiya left this on our Solar Bloom page, word for word: "Fragrance is great but May be my formula for reed diffuser is 60% dpg 20% isopropyl myristate 10% perfume oil and 10% ethanol perfume grade. But throw of scent is low. Can you fix this formula." Sixty per cent DPG and twenty per cent isopropyl myristate are both slow to leave a reed. Only the ten per cent ethanol is fast, and it leaves first. He gets a short burst, then a slow tail.
Before a volatile co-solvent goes in: the flammability check
The fix you are considering, replacing part of the DPG with a faster-evaporating solvent, can change more than throw. Solvents that evaporate faster often ignite more readily, and the hazard classification of a mixture depends on the whole formula. We don't quote flash points or other numbers for any material, and you shouldn't rely on anyone who does without a document. Do this instead.
The replacement ladder: four arms, twelve bottles
Fix everything except the carrier: the same fragrance oil from the same bottle at 20 g per 100 g, the same 120 ml bottle, 5 fibre reeds of the same pack, the same room and shelf. Then step DPG down. The co-solvent is your choice: a compatible solvent you already use, with an SDS, that you know to be more volatile than DPG. DPM, a glycol ether, is generally more volatile and lower in viscosity than DPG and is a common candidate; an Augeo-type solvent (Augeo is a trademark of another company) is another. Whether either suits your oil, only your test shows. CSI sells neither, so a CSI ready-made base is the fourth arm instead.
| Arm | Carrier per 100 g | Master batch (300 g) | DPG share of carrier | What it isolates |
|---|---|---|---|---|
| A · control | 80 g DPG | 60 g oil + 240 g DPG | 100% | Your current formula, now measured |
| B · first rung | 60 g DPG + 20 g co-solvent | 60 g oil + 180 g DPG + 60 g co-solvent | 75% | Does a small change (20% of the batch) move the rate? |
| C · second rung | 40 g DPG + 40 g co-solvent | 60 g oil + 120 g DPG + 120 g co-solvent | 50% | Bigger change (40% of the batch): rate, throw, and stability |
| D · CSI base | 80 g Pure Performance | 60 g oil + 240 g Pure Performance | not stated | A ready-made base, composition unpublished |
Totals for the whole test: 240 g of your oil, 540 g of DPG, 180 g of co-solvent and 240 g of Pure Performance. Why stop at 50%? Because the brief is "switch to a more volatile carrier", and the honest answer is often "partly". If arm C is still far under your band, the next step is a structured trial of more ratios, which is the 500 g multi-ratio trial post. Comparing DPM, an Augeo-type solvent and a ready-made base head to head is the which-co-solvent post.
If you want a second reading on the method, our live guide to testing a diffuser over 30 days with weight loss, intensity, reed condition and room temperature covers the log sheet in more depth; this page adds only the carrier ladder.
Reading the result, and the purchase step
| Pattern | What you see | What it means | Decision |
|---|---|---|---|
| 1 | B inside the band and beats A | A small dose of a faster solvent was enough | Keep DPG as the majority; adopt B; confirm on your next oil |
| 2 | Only C inside the band | DPG needs to be the minority partner for this oil | Adopt C if stable; consider the finer steps in 8316 |
| 3 | D inside the band and beats A; B and C don't | The ready-made base suits this oil better than your solvent mix | Test D on your other oils before you switch the range |
| 4 | Rates rise but sniff scores don't | The carrier now leaves, but carries little fragrance | Look at the oil and its load: rows four and five of the cause table |
| 5 | Nothing moves much; fresh reeds jump | Clogged reeds, not the carrier | Fresh reeds; reconsider the oil; the only-the-reeds-smell post if tips smell strong |
| 6 | C or D clouds, layers or sweats droplets | Stability failed | Reject the arm, however fast it is |
| 7 | Spread inside an arm bigger than the gap between arms | No conclusion yet | Tighten method; more bottles; don't decide on noise |
The purchase step after a pass
Worked example, labelled: a first run of 50 bottles at the series default (100 g fill, 5 reeds). If B or C passed, the CSI side is reeds and bottles: 250 reeds as 2 × 100 + 1 × 50 (₹2,000.00, the same ₹8.00 a reed as any pack from 50 up) and five Gold 120 ML packs (₹5,310.00), ₹7,310.00 in all, ₹146.20 a bottle before oil. If D passed, you need 4,000 g of base. Pure Performance 500 ML is sold by volume and its page gives no density, so weigh 100 ml of it on your scale. If it comes out near 1.0 g per ml, eight 500 ML bottles (₹8,792.00) cover the run. That makes ₹16,102.00 with reeds and bottles, ₹322.04 a bottle before oil. All figures are materials only and exclude your oil, labour, freight, packaging and GST.
Don't jump from a 300 g test to the biggest pack. Check that a fresh pack of the base, or a fresh lot of your co-solvent, behaves like the test lot on your first production bottles; weigh three of them for two weeks. For buying quantities beyond this, see our live guide on whether to buy 1 kg, 5 kg or 25 kg of base when starting. CSI lists no 25 kg base pack, so ask on WhatsApp.
What to buy for this test, and what to skip
Chosen for this test on page statements, price and stock on 7 October 2026, not on any performance data. CSI publishes none for its bases or reeds. Each card says when not to buy.
| Size | Price | Unit price | For this test |
|---|---|---|---|
| 100g | ₹325.00 | ₹3.25 a gram | arm D needs 240 g: three packs (₹975.00), 60 g spare |
| 500 ML | ₹1,099.00 | ₹2.20 a ml | ₹124.00 more than three 100g; buy only if arm D might pass and you want a retest |
| Pack | Price | Per reed | For this test |
|---|---|---|---|
| Pack of 25 | ₹236.00 | ₹9.44 | with the 50: 15 spare for the fresh-reed check |
| Pack of 50 | ₹400.00 | ₹8.00 | 60 reeds for 12 bottles = 50 + 25 |
| Pack of 100 | ₹800.00 | ₹8.00 | same per reed as 50: production |
| Pack of 500 | ₹4,000.00 | ₹8.00 | same per reed: no saving over 50 |
| Pack | Price | Per bottle | For this test |
|---|---|---|---|
| 120 ML Pack of 10 | ₹1,062.00 | ₹106.20 | 2 packs for 12 bottles, 8 spare |
| 50 ML Pack of 10 | ₹826.00 | ₹82.60 | not for this test: a different neck-to-volume ratio |
| Listing | Price | — | Check first |
|---|---|---|---|
| Default Title | ₹354.00 | — | Resolution not stated: check it reads 0.1 g with a known weight first |
| Listing | Price | — | Use |
|---|---|---|---|
| 250 ML | ₹600.00 | — | one 300 g master batch per arm, by weight on the scale |
| 100 ML (separate listing) | ₹300.00 | — | too small for a 300 g master |
Skip for now: the 500 ML of any base before arm D has passed; Lift, Longevity, Depth or Softness as extra arms (each changes the comparison; test one base at a time); the CSI HyperDiffusion Base™, which is out of stock on 7 October 2026; and the Isopropyl Alcohol Spray, which is a cleaner, never a diffuser ingredient. If your oil is a floral, citrus or fruity one, the Lift Base page positions itself for those families, so Lift could replace Pure Performance as arm D. That is the page's positioning, not our test result.
CandleMakingSuppliesIndia sells the bases, fibre reeds, bottles and tools named here. It does not sell DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol, and this page says so. Our base pages publish no composition, density, flash point or SDS in the text we captured. Pure Performance is presented as a comparison arm to test, and we tell you to keep your own blend if it wins.
Every CSI price was checked on 7 October 2026, with stock checked per variant: everything priced here is in stock on that date, and the CSI HyperDiffusion Base™ is out of stock and not offered. Page wording is quoted and attributed to the page.
The g/day rates, the diagram and the sniff scores are illustrative, not CSI test data. The 100 g fill, 20% load, 10 g residue, 45–90-day band and the decision-rule thresholds are labelled worked examples; the rule is yours. For bulk pricing, GST invoicing, and MSDS and IFRA documentation for our fragrance oils on request, message us on WhatsApp at +91 7397976926.
Frequently asked questions
- I Made a Reed Diffuser Using 80 g DPG and 20 g Fragrance Oil, but the Reeds Are Wet and the Room Has Almost No Smell — Is DPG the Wrong Base for This Formula?
- I Made a 120 ml Reed Diffuser with DPG and Six Fibre Reeds, but Only the Reeds Smell Strong — Could the Carrier Be Evaporating Too Slowly?
- I Made a Reed Diffuser with 15% Fragrance Oil and DPG, and the Liquid Is Clear but Very Slow to Wick — How Do I Determine Whether Viscosity Is the Problem?
- My DPG Reed Diffuser Lasts Three Months but Doesn’t Fragrance the Room — How Do I Balance Evaporation Rate and Fragrance Throw?
- I Want to Replace Part of the DPG in My Reed Diffuser Formula — Should I Test DPM, an Augeo-Type Solvent or a Commercial Ready-Made Base?
- My DPG Reed Diffuser Has Almost No Weight Loss After Ten Days — How Do I Run a Controlled Evaporation Test to Compare Alternative Bases?
- I Want to Make a 500 g Reed Diffuser Trial with DPG and a More Volatile Compatible Carrier — How Do I Structure the Test Without Changing Multiple Variables at Once?
- I Am Buying a New Reed Diffuser Base Because DPG Isn’t Working — What Technical Specifications Should I Compare Before Ordering Samples?
Customer reviews: The six reviews at the top of this page are genuine, published Judge.me reviews left by CSI customers on the product pages named on each card — Blue Ocean Fragrance Oil, Gold Reed Diffuser Bottle Pack of 10 (50 ML and 120 ML), Lift Base – Professional Grade Reed & Car Diffuser Base (500 ml), Sacred Sandal Ember Fragrance Oil, Solar Bloom Fragrance Oil, Woody Oud Fragrance Oil. They are general product reviews, not assessments of the reed-diffuser formulation advice on this page. Names, star ratings, dates and products are as recorded by Judge.me and wording is unedited. "Verified buyer" appears only on reviews Judge.me recorded as verified — Pradeep Kumar Dahiya, Sooraj R, snehal Chaudhary, Sooraj R, Renam Dhoundiyal, Urvashi Patel. Reviews below five stars are included as published, not filtered out.
Figures verified 7 October 2026, CSI live pricing: Pure Performance Reed Base Oil 100g ₹325.00 (₹3.25 a gram), 500 ML ₹1,099.00 (₹2.20 a ml); Lift Base 500 ml ₹1,099.00; CSI HyperDiffusion Base™ ₹1,499.00 (out of stock); Fiber Diffuser Reeds (Black) 25 ₹236.00 (₹9.44 a reed), 50 ₹400.00, 100 ₹800.00, 500 ₹4,000.00 (₹8.00 a reed from 50 up); Gold Reed Diffuser Bottle Pack of 10, 120 ML ₹1,062.00 (₹106.20 each), 50 ML ₹826.00 (₹82.60 each); Candle Making Weighing Scale ₹354.00; Silicon Measuring Beaker 250 ML ₹600.00, 100 ML ₹300.00; Isopropyl Alcohol Spray 150 ML ₹383.00 / 1 Litre ₹520.00 (a cleaner, named only to rule it out). Every item priced is in stock on 7 October 2026 except where marked. Per unit = pack price ÷ units, two decimals. CSI does not list DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol.
Non-price figures: "DPG as the only base" and "two weeks" are the reader's (title). The 20 g oil + 80 g carrier per 100 g, the 100 g fill in a 120 ml bottle, 5 fibre reeds (20.3 cm, the page's length), 10 g residue, 90 g usable and the 45–90-day band are labelled worked examples. The 4.2 g in 14 days (0.30 g a day), the diagram lines and the sniff scale are illustrative, not CSI test data. Solvent behaviour is described as general tendencies with no numeric flash points, viscosities or evaporation rates. The 24–48 hour rest and "Blend with 10-30% fragrance oil" are base-page wording. The 50-bottle run assumes a density near 1.0 g/ml that you must confirm by weighing. Costs are materials only and exclude labour, freight, packaging and GST. Diwali 8 November 2026 is a calendar fact.