I Have Finalised a 100 g Reed Diffuser Formula — How Do I Scale It to 10 Kg While Maintaining the Same Fragrance and Carrier Percentages?

I Have Finalised a 100 g Reed Diffuser Formula — How Do I Scale It to 10 Kg While Maintaining the Same Fragrance and Carrier Percentages?

 

British Rose 1 kg ₹3,068.00 Gold 120 ML bottles ₹106.20 each (pack of 10) Black fibre reeds ₹8.00 each from 50 up
Scaling 100 g to 10 kg
Same percentages, same lots, same order of addition, and a 14-day hold that proves the batch matches.
★★★★★
"Fragrance oil is sooo good smell so good we love it a lot"
Arshad ShaikhVerified buyer · Mar 2026
British Rose Fragrance Oil
★★★★★
"In past five years of testing and searching for the best candle fragrance I would say I found what am looking for strong fragrance in cold throw and hot throw and you can go for the minimum percentage in candle still it will give amazing smell well done and all the best"
Emma BecharaJun 2026
British Rose Fragrance Oil
★★★★★
"Nice product"
snehal ChaudharyVerified buyer · May 2026
Gold Reed Diffuser Bottle Pack of 10 (50 ML and 120 ML)
★★★★★
"Good product👍"
Sooraj RVerified buyer · Jul 2026
Lift Base – Professional Grade Reed & Car Diffuser Base (500 ml) For Uplifting, Mood-Boosting Scents
★★★★☆
"I just tried it out , it's absolutely stunning. Super easy to use and such a life saver."
ThenirvaofficialVerified buyer · Mar 2026
Room & Linen Spray Base – Fast-Dry, Zero-Residue (500 g)
★★★★★
"Soy wax quality is the best, which ever products ordered were properly packed and delivered as early as possible, timely response to the inquiries. Good service"
Jaya SawlaniVerified buyer · Nov 2025
Luxury Soy Wax CSI 464 (Flakes Form) For Container Candles
Reviews collected and published through Judge.me on candlemakingsuppliesindia.store. They are general reviews of the products named on each card, not assessments of the advice set out below. Wording is unedited.
✓ Prices verified 7 October 2026, stock checked per size ✓ GST invoice; MSDS and IFRA documentation for oils on request ✓ CSI does not sell DPG, DPM or IPM — we say so
CSI Reed Diffusers · Scaling
A finalised formula is a set of percentages by weight. Multiply every line by 100, keep the same lots and order of addition, reconcile the stock, and hold nine bottles for 14 days before you sell the batch.
× 100
every line of the 100 g formula, by weight · CSI side of a 10 kg run ₹21,556.00, CSI live pricing, October 2026
Quick answers — read this first
How do I scale a 100 g reed diffuser formula to 10 kg and keep the same percentages? Multiply every line by 100, by weight, and change nothing else: same oil, same solvents from the same lots, same order of addition, same rest. In the worked example, 18.0 g oil + 52.0 g DPG + 30.0 g DPM becomes 1,800 g + 5,200 g + 3,000 g = 10,000 g, still 18.0% fragrance.

What usually goes wrong? Not the arithmetic. It is a unit slip (ml weighed as g), a tare left on the scale, a new solvent lot nobody checked, or a tall vessel that was not mixed top to bottom. A stock reconciliation catches the first three; samples from the start and end of filling catch the fourth.

How do I know the 10 kg batch matches the 100 g one? Hold it. Make a fresh 100 g "lab twin" the same day from the same lots, then run 3 twin bottles beside 3 start-of-fill and 3 end-of-fill bottles for at least 14 days, weighing every 2 days. Release only if both production arms sit inside a band you wrote down first.

What does the CSI side cost? For 100 Gold 120 ML bottles, 600 fibre reeds and 2 kg of British Rose: ₹21,556.00. CSI does not sell DPG or DPM — those stay with your solvent supplier.
The short answer
The rule: percentages by weight are the formula; grams are only this batch's instruction. Scale factor 100, every line, no rounding of the oil line.
The process: carrier first, oil in slowly while stirring, the more volatile solvent last, lid on; sample start, middle and end; rest 24–48 hours closed; fill by weight.
The check: stock reconciliation before filling; a 14-day QC hold of 9 bottles (lab twin, start of fill, end of fill) before release.
The yield: 91 sellable 100 g bottles from 10 kg after QC bottles, two retains and a 1% loss allowance (worked example).
Batch sheet: 100 g lab formula → 10 kg Worked example. Multiply every line by 100; no percentage moves. Line Lab 100 g × 100 % w/w Fragrance oil (British Rose) 18.0 g 1,800 g 18.0% DPG (your supplier) 52.0 g 5,200 g 52.0% DPM (your supplier) 30.0 g 3,000 g 30.0% Total 100.0 g 10,000 g 100.0% Production sequence 1 Weigh carrier first 2 Add oil slowly, stirring 3 Mix lid on 4 Sample start · mid · end 5 Rest 24–48 h, closed 6 Fill 100 g each 7 Hold 14 days QC QC hold: 9 bottles, 14+ days L · lab twin, 100 g, same lots × 3 P1 · start-of-fill bottles × 3 P2 · end-of-fill bottles × 3 Weigh every 2 days → g/day Release if P1 and P2 sit inside your own band around L Reconciliation (weigh stock) Oil stock before − after = 1,800 g DPG stock before − after = 5,200 g DPM stock before − after = 3,000 g Full vessel − empty vessel = 10,000 g, less what you sampled Any gap: stop before filling Illustrative worked example, not CSI test data. CSI does not sell DPG or DPM.
The batch sheet multiplies every line by 100; the percentage column never moves. The sequence below it and the two boxes are the controls that make the grams come out right: a stock reconciliation before filling and a nine-bottle QC hold before release. Worked example with illustrative figures, not CSI test data.
Straight answer
I have finalised a 100 g reed diffuser formula. How do I scale it to 10 kg while keeping the same fragrance and carrier percentages?
Treat the percentages by weight as the formula and multiply every gram line by 100. If your finalised 100 g is 18.0 g fragrance oil, 52.0 g DPG and 30.0 g DPM (our worked example — put your own lines in), the 10 kg batch is 1,800 g oil, 5,200 g DPG and 3,000 g DPM, 10,000 g in all, still 18.0% fragrance. Then keep everything else identical to the 100 g you proved: the same oil and solvents, ideally the same lots; the same order of addition; the same rest. What changes is the equipment: a scale that covers your biggest single weighing, a closed vessel with headroom, a stirrer that reaches the bottom. Prove the batch matches before you sell it: a 100 g lab twin made the same day, three of its bottles beside three from the start and three from the end of filling, weighed every 2 days for at least 14 days, against a release band you set first.
One line: same percentages, same materials, same order — and a 14-day hold that proves it, because the scale-up is the step where a ml slips in for a gram.
Scaling a British Rose formula? Two 1 kg packs (₹6,136.00) cover 1,800 g of production oil and the 18 g lab twin, with 182 g left for retains.
Buy British Rose 1 kg

The scaling sheet, line by line

The formula is a set of percentages. Grams are just what those percentages look like at one batch size.

Your 100 g formula is "finalised" because it passed something: a 14–30 day weight-loss test, a sniff panel, a stability check at room, warm and cool positions. What passed was the ratio, made in a particular way, from particular lots. The scaling sheet carries the ratio across unchanged and writes down the grams for this batch size only. Put it on paper (or a spreadsheet you print) before anything is opened, with one row per material, and calculate the production column from the percentage column rather than from the lab grams; then if your lab batch was 100 g the numbers match, and if a future lab batch is 250 g the sheet still works.

Here is the worked example we will carry through the page. It is a three-part formula of the kind this series deals with, a fragrance oil in a DPG and DPM carrier; your formula may have more lines (a little IPM, a second oil, a dye) or fewer (oil plus a single ready-made base). The method does not change with the number of lines.

Scaling sheet · worked example
Every line × 100. The percentage column is the formula; the grams column is the instruction for this batch size only.
Line Lab batch Production 10 kg % by weight Who supplies it
Fragrance oil (British Rose) 18.0 g 1,800 g 18.0% CSI (2 × 1 kg)
DPG 52.0 g 5,200 g 52.0% Your solvent supplier — CSI does not sell DPG
DPM 30.0 g 3,000 g 30.0% Your solvent supplier — CSI does not sell DPM
Total 100.0 g 10,000 g 100.0% Factor 100

Three rules make the sheet trustworthy. One unit: grams on every line, including the fragrance oil, which many people still measure by volume out of habit. No rounding of small lines: 18.0 × 100 is 1,800 g, not "about 1.8 kg" — on a formula with a 0.5% additive the additive line is 50 g at 10 kg and must be weighed as carefully as the big ones. A total that checks itself: the production column must add to exactly 10,000 g. If it does not, a line was mis-multiplied; a common one is scaling the oil ×10 by habit from an earlier 1 kg batch, which would give 180 g instead of 1,800 g and a load of 2.1% instead of 18.0%.

Write the sheet for the percentages, not the grams
Column A: material and supplier lot number. Column B: % by weight to one decimal. Column C: = B × batch size ÷ 100. Column D: actual weighed, entered at the bench. Column E: initials. Column F: stock weight before and after. When D differs from C by more than your tolerance on any line, you stop and correct before the next line goes in.

If your finalised carrier is a CSI ready-made base rather than your own solvents, the sheet is simpler and the only twist is buying: a 20 g oil + 80 g base formula needs 2,000 g oil and 8,000 g base at 10 kg, and CSI sells its bases by the 500 ml bottle. The density step that turns grams into bottles is covered in the 100 × 120 ml density calculation and fair formulas by weight when densities differ; the short version is in pick card 6 below.

Weighing at 10 kg: where precision is won and lost

Makers often worry that a big batch will be less accurate. In relative terms it is usually more accurate. A scale that reads in 0.1 g steps, used on an 18.0 g oil line, carries a reading uncertainty of about 0.56% of that line. A platform scale reading in 1 g steps, used on the 1,800 g production line, carries about 0.06%. The batch gets bigger faster than the scale's step does (illustrative scale steps; read your own scale's label).

What goes wrong at 10 kg is not resolution. It is the human part of weighing: a forgotten tare with a jug still on the platform, a reading taken before the display settles, a line weighed twice, and above all a unit slip. Fragrance oils and solvents do not weigh 1 g per ml; if someone pours "1,800" on a measuring jug instead of a scale, and the oil happens to weigh 0.95 g per ml (a labelled worked example — weigh 100 ml of yours), only 1,710 g goes in, 90 g short, and the batch drops to 17.3%. That is a change you might not sniff on day 1 and might well see in g/day by day 14.

Two habits remove almost all of it. First, tare discipline: write the empty-vessel weight on the sheet, and write the running gross weight after each line, so each line's net is a subtraction anyone can check. Second, stock reconciliation: weigh each stock container before and after; the difference must equal the sheet line. The oil container should be 1,800 g lighter, the DPG 5,200 g lighter, the DPM 3,000 g lighter. A reconciliation takes ten minutes and is the only check that catches an error after the liquid has disappeared into the vessel.

Don't do this: scale up and change the fragrance load "while you're at it" because the lab bottles seemed a touch soft, or swap DPM for a cheaper co-solvent for the big run. A finalised formula changed at scale-up is an untested formula made in the largest quantity you have ever made. Fix: scale exactly what passed. If you want to try 20% or another solvent, run it as a new 100 g test with 3 bottles per arm for 14–30 days, and scale that only when it passes.

Vessel, mixer, scale: the equipment the batch needs

At 100 g your equipment was a beaker, a lab scale and a stirring rod. At 10 kg each of those has to be replaced by something sized for the job, and none of the replacements should change the chemistry.

The vessel

Ten kilograms of a glycol-based carrier and oil is roughly ten litres or a little more, depending on your materials' densities. Choose a closed vessel with real headroom, so you can mix without splashing (as a judgement, about half as much space again). It must be clean, dry and made of a material your solvent and fragrance suppliers' SDS documents allow — stainless steel is a common choice; some plastics can be softened or stained by fragrance materials and solvents, so check rather than assume. A tap or valve near the bottom makes filling by weight far easier than ladling. Keep the lid on through mixing and resting: if your formula includes a more volatile solvent such as DPM, an open vessel in a warm room can lose some of it, and the loss shows on the scale if you weigh the closed vessel before and after.

The scale

You need two: a platform scale whose capacity covers your heaviest single weighing including the container (for the DPG line here, 5.2 kg plus the jug), and a small scale for the lab twin, QC bottles and every-2-days weigh-ins. CSI sells the second kind, the Candle Making Weighing Scale, and its page states no capacity or resolution — read the label on yours before trusting it with anything (the cluster's first-trial buying guide covers the small-scale kit). CSI lists no platform scale; buy one from a supplier who states capacity and step, and check it with a known weight before the batch.

The mixer

The 100 g formula was homogeneous because a rod could reach every part of the beaker. A tall 15 litre vessel is different: a dense oil or a less soluble component can settle, and a handheld mixer moving the top third leaves the bottom alone. Use a long paddle that reaches the bottom, or a stirrer sized to the vessel, and mix for a fixed, written time. Then let the evidence decide whether it was enough, through the start-of-fill versus end-of-fill comparison in the QC hold. We sell a handheld mixer, the CSI Pro Mixer, and we would rather you used it where it fits: the lab twin and re-mixing samples, not the full 10 kg.

"The batch was homogeneous at 100 g because a stirring rod touched every drop. At 10 kg you have to prove it."
— CandleMakingSuppliesIndia

Order of addition, mixing, rest and filling

The order you used at 100 g is part of the formula. If you dissolved the oil in DPG first and added DPM after, do that at 10 kg; if you poured everything into a beaker together and stirred, at least write down that you did, and consider the more controlled order below for the big batch, after checking it at 100 g. The walkthrough is the sequence we would use for the worked example.

1
Prepare and record. Clean, dry, closed vessel on the platform scale; empty weight written on the sheet; lot numbers of oil, DPG and DPM written beside each line; stock containers weighed and recorded.
2
Carrier in first. Weigh in the 5,200 g of DPG, the solvent your oil dissolved in best at 100 g. Record the gross weight.
3
Oil in slowly, stirring. Add the 1,800 g of fragrance oil in a thin stream while stirring. Adding oil into the solvent, rather than solvent onto a puddle of oil, gives each portion a lot of solvent to dissolve into. Record the gross weight.
4
Volatile solvent last, lid on. Add the 3,000 g of DPM, the more volatile solvent, last; close the lid between additions. Mix for a written time with a paddle that reaches the bottom. Weigh the closed vessel: the gross should equal empty weight + 10,000 g.
5
Sample and rest. Draw a 100 g sample from the top and one from the bottom (or the tap) into clear glass, labelled. Rest the closed vessel for 24–48 hours away from sun and heat — the window CSI base pages give before bottling, and a sensible default for your own carrier. Check the two samples for haze, streaks or a layer before filling.
6
Reconcile, then fill by weight. Weigh the stock containers again; each must be lighter by its sheet line. Fill each bottle to 100 g on the small scale, not to a line on the glass. Number the bottles in filling order; the first three and last three go into the QC hold.
7
Hold, test, release. Run the 9-bottle QC hold for at least 14 days (below). Store the filled bottles sealed and labelled "hold" until the release rule is met.

If your formula is 20 g oil + 80 g CSI base, steps 2–4 collapse into "base first, oil in slowly while stirring, lid on", and the page's own 24–48 hour rest applies. If your lab notes show you mixed the other way round and it passed, do not change it at scale-up; test the new order at 100 g first.

Safety, briefly and plainly
Ten litres of solvent and fragrance is a different quantity to have open in a room. Flammability and hazard labelling depend on your full formula and on each supplier's SDS: read them for DPG, DPM and the oil before the batch, work with ventilation and no flames or heaters nearby, wear gloves and eye protection (fragrance oils and solvents can irritate skin and eyes), keep children and pets out of the room, and label the vessel. This is general practice, not legal advice on storage or labelling rules.

Cause table: why a big batch drifts from the small one

When a scaled batch does not match the lab, there are six places to look, and they leave different fingerprints. Keep them apart: solvent lot, fragrance load and oil, mixing, reeds and fill, environment, and measurement. The table is written for this page's question — a scale-up that has just been made. If your 5 kg batch is already weak and you are diagnosing it after the fact, the production-variable checklist in the 500 g versus 5 kg weak-throw post goes deeper.

Cause table · why a 10 kg batch can drift from the 100 g formula
Read across: cause → what you would see → the check that separates it from the others → fix. Run the reconciliation before anything else.
Cause What you would see Discriminating check Fix
Carrier (solvent) lot or supplier changed — the DPG or DPM drum is a new lot, or you bought from someone else for the big run Production bottles all move the same way against the lab twin, start and end of fill alike; odour or colour of the neat carrier differs from your retained lab carrier Make two 100 g batches side by side: same oil, one with retained lab-lot carrier, one with production-lot carrier; 3 bottles each Qualify the new lot first (incoming QC for a new base lot); never let a lot change ride on a scale-up
Fragrance load or oil character — a sheet error (one line ×10 instead of ×100), or a different oil lot Sniff clearly stronger or weaker in every production bottle; with a ×10 oil error the load falls to 2.1% Reconcile: oil stock weight before minus after must equal 1,800 g; compare the oil lot number with the lab lot Correct and remake; if the oil lot changed, a 100 g compatibility check comes first (new oil lot)
Incomplete mixing — oil or one solvent layered in a tall vessel Start-of-fill and end-of-fill bottles differ from each other, not just from the lab twin; a haze or streaks when you tilt a sample against light P1 versus P2 in the QC hold; a 100 g sample from the top and bottom held in clear glass for 48 hours Re-mix the whole vessel for longer, lid on; sample again before filling
Reeds, bottle or fill — QC bottles filled with different reed packs, counts or fill weights Wide spread inside one arm; one bottle far from its two partners Check fill weights (each bottle weighed on filling) and that every QC bottle took reeds from one pack Same reed pack, same count (6), same fill (100 g) in every QC bottle
Environment during mixing — open vessel, warm room, sun on the drum Full-vessel weight after mixing below the sum of what you weighed in; the batch smells thinner at the top Weigh the closed vessel after mixing and after the rest; a loss you can see on the scale is evaporation Mix and rest with the lid on, out of sun and away from heat
Measurement error — ml used for g, wrong tare, scale over capacity Reconciliation gap; with a ml-for-g slip on the oil (0.95 g per ml, labelled) the oil falls 90 g short and the load to 17.3% Stock reconciliation line by line, then the weighing log: every net weight a subtraction someone else can check One unit (grams) on the sheet; tare written down; a scale whose capacity covers the largest single weighing

The reconciliation is first because it is cheap and final. If every stock container is lighter by exactly its sheet line and the closed vessel weighs empty + 10,000 g, measurement error and the ×10 slip are excluded before you have spent a day on a sniff test.

QC samples and the 14-day hold before release

A reconciled sheet proves you put the right grams in. Only the hold proves the batch behaves like the formula.

The hold compares the production batch with the formula made correctly at lab size, using the lots in the vessel. That is why the reference is a lab twin — a fresh 100 g batch made the same day from the same oil, DPG and DPM — rather than your original test bottles, which are older, from earlier lots, and partly used. Three arms, three bottles each, every bottle 100 g by weight in a Gold 120 ML bottle with 6 black fibre reeds from one pack, all in one room, with the room's temperature and humidity written down at each weighing.

The QC hold · three arms, nine bottles
Same Gold 120 ML bottle, 6 black fibre reeds from one pack, 100 g fill, one room, weighed every 2 days. Figures in the last column are illustrative, not CSI test data.
Arm Made from Bottles What it answers Illustrative mean g/day
L · lab twin A fresh 100 g batch made the same day from the same oil, DPG and DPM lots 3 What this formula does when made correctly at 100 g 1.20
P1 · start of fill Production bottles 1, 2 and 3 off the vessel 3 Did the top of the batch match the formula? 1.16 (-3.3%)
P2 · end of fill The last three production bottles 3 Did the bottom of the batch match it? 0.98 (-18.3%)

Weigh every bottle every 2 days and work out g/day as (start weight − current weight) ÷ days. At day 14 (better, day 30 if your launch allows), compare each production arm's mean with the lab twin's. Run a blind sniff at a fixed distance and time with two or three people who don't know which bottle is which, and look at every bottle against light for haze, layering or sediment, including one kept in a warm position and one in a cool one.

Your release rule (in-house, set before day 1; the figures here are an example, not a standard): release the batch if both P1 and P2 means are within ±10% of the lab twin's mean g/day, no production bottle shows haze or layering that the twin doesn't, and the blind sniff does not rank production below the twin. In the illustrative readings above, P1 sits at -3.3% and passes; P2 sits at -18.3% and fails. That pattern — top fine, bottom different — points to mixing, not formula: re-mix the vessel, re-sample, and repeat the comparison on the bottles you refill. If both arms had failed in the same direction, the table would point you at the carrier lot or the oil line instead.

Keep two 100 g retains of the released batch and one of the lab twin, sealed in glass, labelled with date and lot numbers, out of light. The next time a customer says "this one is weaker", a retain and a 14-day comparison will answer whether the batch changed or the room did. The method for long-term weight-loss testing is set out in the 30-day reed diffuser test; this page uses a shortened version of it as a release check.

Don't do this: judge the batch on day 2 because the lab twin and the production bottles "smell the same". On day 2 every fresh diffuser smells of its reed tips. Fix: hold to at least day 14 of weighed g/day before release; if Diwali or a client date is pressing, mix earlier, not test shorter.
Diwali is 8 November 2026, 32 days from 7 October 2026. Mixing, a 48-hour rest and a 14-day hold take about 16 days before the first bottle can be released, plus your filling and dispatch time. If a festive 10 kg run depends on it, order this week and ask us to confirm dispatch to your city, with a GST invoice.
WhatsApp a festive order

Buying for the run, and what to buy from whom

Be clear about who supplies what. CSI does not sell DPG, DPM, IPM, Augeo-type solvents or perfumer's alcohol; the only alcohol CSI lists is an Isopropyl Alcohol Spray, which is a jar cleaner and has no place in a diffuser. Your 5,200 g of DPG and 3,000 g of DPM therefore come from the supplier whose lots made the 100 g formula. Ask them for the same grade and, if you can, one lot for the whole run, plus the SDS for each. If the lot has changed since your lab batch, qualify it at 100 g first (incoming checks for a new lot).

From CSI, the worked example buys the oil, bottles and reeds. The yield arithmetic decides the quantities:

Yield and purchase · worked example
10 kg batch, 100 g fill, 6 reeds per bottle. The 1% loss allowance is a worked example — measure your own vessel and filling loss.
Item Arithmetic Quantity CSI price
Sellable bottles 10,000 − 600 (6 QC bottles) − 200 (2 retains) − 100 (1% loss), ÷ 100 g 91 —
Bottles to buy 91 sellable + 6 production QC + 3 lab twin 100 (10 packs of 10 × 120 ML) ₹10,620.00
Fibre reeds (black) 100 bottles × 6 600 (500 + 100) ₹4,800.00
British Rose oil 1,800 g production + 18 g lab twin = 1,818 g 2 × 1 kg (182 g spare) ₹6,136.00
CSI side total oil + bottles + reeds — ₹21,556.00 (₹236.88 per sellable bottle)

The per-bottle figure covers only the CSI items; it excludes your DPG and DPM, labour, freight, packaging and GST. Three buying notes, two of them against our own interest. Reeds are flat per reed from the 50-pack up (₹8.00 each), so a 500-pack saves nothing over five 100-packs; buy the count you need. Two 1 kg packs of British Rose are cheaper than four 500 g packs by ₹236.00, so here the bigger pack does win. And if your finalised carrier is your own DPG/DPM blend and it passed, keep it for the scale-up: we will not pretend a CSI base is a drop-in improvement at this stage. A base swap is a new formula, tested at 100 g first — the planning for that sits in the pilot-batch post and, for 25 kg base orders, the 25 kg documentation request list.

If your formula is built on a CSI base, ask us on WhatsApp whether the 16 or 17 bottles you need can come from one lot, and for any technical data available before the run; the base pages themselves publish no composition, density, flash point or SDS.

This page is for you if: your 100 g formula has already passed a weighed 14–30 day test and you are about to make it at 5–25 kg. It is not for you if: the formula is still changing, you are choosing between bases (start at choosing between three tested bases) or a scaled batch has already failed (production variables).

What to buy at CSI for this batch

Chosen on what the pages state, price and stock on 7 October 2026, not on performance claims. Each card says when not to buy.

1
Fragrance oil · the 18% line
British Rose Fragrance Oil
The worked example uses it because its page gives a reed-diffuser range — "reed diffusers (10-30%)" — and describes "fresh, dewy rose petals with subtle green undertones and a soft floral finish". That range is the page's usage note, not a performance promise for your carrier. For a 10 kg run at 18% you need 1,800 g, plus 18 g for the lab twin: two 1 kg packs leave 182 g for retains and a re-test. Limitation: if your finalised formula used a different oil, this card does not apply — the scale-up must use the oil you tested, from a lot you have checked.
Size Price Per gram 100 g bottles at 18% Stock
15 gm ₹94.40 ₹6.29 0 In stock
50 gm ₹212.40 ₹4.25 2 In stock
100 gm ₹342.20 ₹3.42 5 In stock
500 gm ₹1,593.00 ₹3.19 27 In stock
1 kg ₹3,068.00 ₹3.07 55 In stock
Two 1 kg packs ₹6,136.00; four 500 g packs would cost ₹236.00 more. Buy British Rose 1 kg
2
Bottle · production and QC
Gold Reed Diffuser Bottle Pack of 10 (120 ML)
One bottle type for production and for all nine QC bottles, so the hold compares formula, not glass. Per bottle ₹106.20 in packs of 10. The page lists "Size: 50 and 100ml" although the variant says 120 ML, and states no neck diameter — weigh your 100 g fill rather than trusting a line on the glass. Limitation: no bulk tier above the pack of 10 is listed; for 100 bottles ask on WhatsApp for dispatch timing.
Pack Price Per bottle Stock
50 ML × 10 ₹826.00 ₹82.60 In stock
120 ML × 10 ₹1,062.00 ₹106.20 In stock
10 packs of 120 ML = ₹10,620.00 for 100 bottles. Buy Gold bottles
3
Reeds · same pack for every QC bottle
Fiber Diffuser Reeds (Black)
Fibre reeds, 20.3 cm; the page claims "no swelling, no clogging" and "Consistent diffusion from day 1 to day 30" — page claims, which your QC hold tests rather than assumes. CSI sells fibre reeds, not rattan. Limitation: the page states no diameter, so if your 100 g formula was proved on another reed, the scale-up is not the moment to switch.
Pack Price Per reed Stock
25 ₹236.00 ₹9.44 In stock
50 ₹400.00 ₹8.00 In stock
100 ₹800.00 ₹8.00 In stock
500 ₹4,000.00 ₹8.00 In stock
600 reeds = 500 + 100 for ₹4,800.00 (six 100-packs cost the same). Buy black fibre reeds
4
Weighing · lab twin and retains
Candle Making Weighing Scale
A digital scale reading "grams or ounces" — fine for the 100 g lab twin, the QC bottles and the every-2-days weigh-ins if its resolution suits you. The page states no capacity and no resolution, so read its label before you trust it for anything. Limitation, plainly: do not use it for the 5,200 g DPG line unless its label covers that weight; a 10 kg batch needs a platform scale whose capacity and step you know, and CSI does not list one.
Item Price Stock
Candle Making Weighing Scale ₹354.00 In stock
Silicon Measuring Beaker 100 ML ₹300.00 In stock
Silicon Measuring Beaker 250 ML ₹600.00 In stock
Scale ₹354.00; beakers for the lab twin and samples. Buy the scale
5
Mixing · lab and sub-samples
CSI Pro Mixer - Cordless Handheld Mixer
A cordless handheld mixer for candle, diffuser and soap work. Useful for the 100 g lab twin and for re-homogenising a drawn sample. Limitation, against our own sale: the captured page states no capacity or speed, and a handheld mixer is unlikely to turn over a full 10 kg vessel from top to bottom. For the production batch use a long paddle or a stirrer sized to your vessel, and let the P1/P2 comparison tell you whether the mix was enough.
Item Price Stock
CSI Pro Mixer ₹349.00 In stock
₹349.00 — a lab tool, not a 10 kg mixer. Buy the Pro Mixer
6
Only if your finalised carrier is a CSI base
Pure Performance Reed Base Oil (100g / 500 ML)
If your 100 g formula was 20 g oil + 80 g Pure Performance, the 10 kg sheet needs 8,000 g of base. CSI sells it by volume, and the page publishes no density, composition, flash point or SDS, so weigh 100 ml yourself: at a labelled 1.00 g per ml that is 8,000 ml, 16 bottles (₹17,584.00); at 0.96 g per ml (worked example) it is 8,333 ml, 17 bottles (₹18,683.00). The page says "Blend with 10-30% fragrance oil" and to rest the blend 24-48 hours before bottling. Limitation: if your formula is DPG and DPM, do not swap in this base at scale-up — that is a new formula needing its own test.
Size Price Per unit Stock
100g ₹325.00 ₹3.25 per g In stock
500 ML ₹1,099.00 ₹2.20 per ml In stock
Only for a formula already proved on this base. See Pure Performance

Skip for now: a second fragrance or a load change folded into this run; the White fibre reeds if your formula was proved on black (different pack, same length, and its page copy describes "black fiber reeds" — a listing error worth knowing); and any reed or bottle quantity beyond the 100 this batch fills.

The CSI principle
Scale the percentages, not your confidence. Reconcile the stock, then make the batch earn its release.
Every line × 100, one unit, same lots and order; a lab twin, start-of-fill and end-of-fill bottles held 14 days against a band you set first. CSI side for 100 bottles: ₹21,556.00.
Why trust this guide

CandleMakingSuppliesIndia sells fragrance oils, ready-made reed diffuser bases, fibre reeds and bottles, not finished diffusers. This page still tells you that we sell no DPG, DPM, IPM, Augeo-type solvent or perfumer's alcohol, that our base pages publish no composition, density, flash point or SDS, that our mixer and scale pages state no capacity, and that a scale-up should not swap in our base.

Every CSI price was checked on the live store on 7 October 2026, with stock checked per size; every item priced here is in stock on that date. Page wording is quoted and attributed as the page's own.

The formula, densities, 1% loss allowance, illustrative g/day readings and ±10% release band are worked examples, labelled; your release rule is yours. Nothing here is CSI test data. For bulk pricing, GST invoicing, and MSDS and IFRA documentation for our fragrance oils on request, message us on WhatsApp at +91 7397976926.

Frequently asked questions

How do you scale up a reed diffuser recipe?
By weight: keep every percentage and multiply each gram line by the scale factor (100 for 100 g to 10 kg). Keep the same materials, lots and order of addition, then check the batch against a fresh lab-size twin before release.
Should I measure reed diffuser oil by weight or by volume for a big batch?
By weight, every line. Oils and solvents do not weigh 1 g per ml, so measuring by volume shifts the load: in the worked example a ml-for-g slip on the oil drops the batch from 18.0% to 17.3%.
How long should a reed diffuser blend rest before bottling?
CSI's base pages say to rest the blend for 24–48 hours before bottling. For your own carrier, use the rest your 100 g formula had, in a closed vessel away from heat and sun.
Why does my big reed diffuser batch smell different from my small test batch?
Usually one of six things: a new solvent lot, a sheet or weighing error on the oil line, incomplete mixing in a tall vessel, different reeds or fills in the comparison, evaporation from an open vessel, or a unit slip. A stock reconciliation and start-versus-end-of-fill samples separate most of them.
What equipment do I need to make 10 kg of reed diffuser liquid?
A closed vessel with headroom in a material your SDS documents allow, a platform scale that covers your biggest single weighing, a small scale for samples, a paddle or stirrer that reaches the bottom, and labelled glass for retains.
Can I switch to a ready-made base when I scale up my DPG formula?
Not as part of the scale-up. A different carrier is a different formula: test it at 100 g with 3 bottles per arm for 14–30 days first. If your DPG formula passed, scaling it as it is will usually be the safer route.
100 g formula → 10 kg
Multiply every line by 100, reconcile the stock, and hold nine bottles for 14 days before you sell.
CSI side for the worked example: two 1 kg British Rose, ten 120 ML Gold bottle packs and 600 black fibre reeds, ₹21,556.00. Your DPG and DPM stay with your solvent supplier. Send us your sheet on WhatsApp and we will confirm stock and dispatch before you mix.
Shop Gold Reed Diffuser Bottles Confirm a 10 kg run on WhatsApp
Editorial standards & sources
About this guide: part of CSI's series on reed diffuser formulation with DPG, DPM, IPM and Augeo-type carriers, in the cluster on buying materials and scaling (8381–8400). It covers the scaling sheet, weighing precision, equipment, order of addition, the cause table for drift, the 14-day QC hold and the purchase for a 10 kg run.

Customer reviews: The six reviews at the top of this page are genuine, published Judge.me reviews left by CSI customers on the product pages named on each card — British Rose Fragrance Oil, Gold Reed Diffuser Bottle Pack of 10 (50 ML and 120 ML), Lift Base – Professional Grade Reed & Car Diffuser Base (500 ml) For Uplifting, Mood-Boosting Scents, Luxury Soy Wax CSI 464 (Flakes Form) For Container Candles, Room & Linen Spray Base – Fast-Dry, Zero-Residue (500 g). They are general product reviews, not assessments of the reed-diffuser formulation advice on this page. Names, star ratings, dates and products are as recorded by Judge.me and wording is unedited. "Verified buyer" appears only on reviews Judge.me recorded as verified — Arshad Shaikh, snehal Chaudhary, Sooraj R, Thenirvaofficial, Jaya Sawlani. The reviews from Emma Bechara are published but not recorded as verified, and carry no badge. Reviews below five stars are included as published, not filtered out.

Figures verified 7 October 2026, CSI live pricing: British Rose Fragrance Oil 15 g ₹94.40, 50 g ₹212.40, 100 g ₹342.20, 500 g ₹1,593.00, 1 kg ₹3,068.00 (per gram ₹6.29, ₹4.25, ₹3.42, ₹3.19, ₹3.07); Gold Reed Diffuser Bottle pack of 10, 50 ML ₹826.00 (₹82.60 each), 120 ML ₹1,062.00 (₹106.20 each); Fiber Diffuser Reeds (Black) 25 ₹236.00 (₹9.44 each), 50 ₹400.00, 100 ₹800.00, 500 ₹4,000.00 (₹8.00 each); Candle Making Weighing Scale ₹354.00; Silicon Measuring Beaker 100 ML ₹300.00, 250 ML ₹600.00; CSI Pro Mixer ₹349.00; Pure Performance Reed Base Oil 100g ₹325.00, 500 ML ₹1,099.00 (₹2.20 per ml). All in stock on 7 October 2026. CSI lists no DPG, DPM, IPM, Augeo-type solvent, perfumer's alcohol, mixing vessel or platform scale.

Non-price figures: the 100 g formula (18.0 g oil, 52.0 g DPG, 30.0 g DPM) is a worked example standing in for the reader's own; the 0.95 g per ml and 0.96 g per ml densities, the 0.1 g and 1 g scale steps, the 1% loss allowance, the ±10% release band and every g/day figure are labelled illustrations, not CSI test data. The 24–48 hour rest and the "Blend with 10-30% fragrance oil" and "reed diffusers (10-30%)" ranges are quoted from CSI pages as usage notes, not performance promises. Costs are materials only and exclude labour, freight, packaging and GST. Diwali 8 November 2026 is a calendar fact.
Back to blog